diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd')
19 files changed, 1318 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mfd/88pm860x.txt b/Documentation/devicetree/bindings/mfd/88pm860x.txt new file mode 100644 index 00000000..63f3ee33 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/88pm860x.txt @@ -0,0 +1,85 @@ +* Marvell 88PM860x Power Management IC + +Required parent device properties: +- compatible : "marvell,88pm860x" +- reg : the I2C slave address for the 88pm860x chip +- interrupts : IRQ line for the 88pm860x chip +- interrupt-controller: describes the 88pm860x as an interrupt controller (has its own domain) +- #interrupt-cells : should be 1. + - The cell is the 88pm860x local IRQ number + +Optional parent device properties: +- marvell,88pm860x-irq-read-clr: inicates whether interrupt status is cleared by read +- marvell,88pm860x-slave-addr: 88pm860x are two chips solution. <reg> stores the I2C address + of one chip, and this property stores the I2C address of + another chip. + +88pm860x consists of a large and varied group of sub-devices: + +Device Supply Names Description +------ ------------ ----------- +88pm860x-onkey : : On key +88pm860x-rtc : : RTC +88pm8607 : : Regulators +88pm860x-backlight : : Backlight +88pm860x-led : : Led +88pm860x-touch : : Touchscreen + +Example: + + pmic: 88pm860x@34 { + compatible = "marvell,88pm860x"; + reg = <0x34>; + interrupts = <4>; + interrupt-parent = <&intc>; + interrupt-controller; + #interrupt-cells = <1>; + + marvell,88pm860x-irq-read-clr; + marvell,88pm860x-slave-addr = <0x11>; + + regulators { + BUCK1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + LDO1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <2800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + rtc { + marvell,88pm860x-vrtc = <1>; + }; + touch { + marvell,88pm860x-gpadc-prebias = <1>; + marvell,88pm860x-gpadc-slot-cycle = <1>; + marvell,88pm860x-tsi-prebias = <6>; + marvell,88pm860x-pen-prebias = <16>; + marvell,88pm860x-pen-prechg = <2>; + marvell,88pm860x-resistor-X = <300>; + }; + backlights { + backlight-0 { + marvell,88pm860x-iset = <4>; + marvell,88pm860x-pwm = <3>; + }; + backlight-2 { + }; + }; + leds { + led0-red { + marvell,88pm860x-iset = <12>; + }; + led0-green { + marvell,88pm860x-iset = <12>; + }; + led0-blue { + marvell,88pm860x-iset = <12>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt new file mode 100644 index 00000000..c3a14e0a --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/ab8500.txt @@ -0,0 +1,159 @@ +* AB8500 Multi-Functional Device (MFD) + +Required parent device properties: +- compatible : contains "stericsson,ab8500"; +- interrupts : contains the IRQ line for the AB8500 +- interrupt-controller : describes the AB8500 as an Interrupt Controller (has its own domain) +- #interrupt-cells : should be 2, for 2-cell format + - The first cell is the AB8500 local IRQ number + - The second cell is used to specify optional parameters + - bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + +The AB8500 consists of a large and varied group of sub-devices: + +Device IRQ Names Supply Names Description +------ --------- ------------ ----------- +ab8500-bm : : : Battery Manager +ab8500-btemp : : : Battery Temperature +ab8500-charger : : : Battery Charger +ab8500-codec : : : Audio Codec +ab8500-fg : : vddadc : Fuel Gauge + : NCONV_ACCU : : Accumulate N Sample Conversion + : BATT_OVV : : Battery Over Voltage + : LOW_BAT_F : : LOW threshold battery voltage + : CC_INT_CALIB : : Coulomb Counter Internal Calibration + : CCEOC : : Coulomb Counter End of Conversion +ab8500-btemp : : vtvout : Battery Temperature + : BAT_CTRL_INDB : : Battery Removal Indicator + : BTEMP_LOW : : Btemp < BtempLow, if battery temperature is lower than -10°C + : BTEMP_LOW_MEDIUM : : BtempLow < Btemp < BtempMedium,if battery temperature is between -10 and 0°C + : BTEMP_MEDIUM_HIGH : : BtempMedium < Btemp < BtempHigh,if battery temperature is between 0°C and“MaxTemp + : BTEMP_HIGH : : Btemp > BtempHigh, if battery temperature is higher than “MaxTemp +ab8500-charger : : vddadc : Charger interface + : MAIN_CH_UNPLUG_DET : : main charger unplug detection management (not in 8505) + : MAIN_CHARGE_PLUG_DET : : main charger plug detection management (not in 8505) + : MAIN_EXT_CH_NOT_OK : : main charger not OK + : MAIN_CH_TH_PROT_R : : Die temp is above main charger + : MAIN_CH_TH_PROT_F : : Die temp is below main charger + : VBUS_DET_F : : VBUS falling detected + : VBUS_DET_R : : VBUS rising detected + : USB_LINK_STATUS : : USB link status has changed + : USB_CH_TH_PROT_R : : Die temp is above usb charger + : USB_CH_TH_PROT_F : : Die temp is below usb charger + : USB_CHARGER_NOT_OKR : : allowed USB charger not ok detection + : VBUS_OVV : : Overvoltage on Vbus ball detected (USB charge is stopped) + : CH_WD_EXP : : Charger watchdog detected +ab8500-gpadc : HW_CONV_END : vddadc : Analogue to Digital Converter + SW_CONV_END : : +ab8500-gpio : : : GPIO Controller +ab8500-ponkey : ONKEY_DBF : : Power-on Key + ONKEY_DBR : : +ab8500-pwm : : : Pulse Width Modulator +ab8500-regulator : : : Regulators +ab8500-rtc : 60S : : Real Time Clock + : ALARM : : +ab8500-sysctrl : : : System Control +ab8500-usb : ID_WAKEUP_R : vddulpivio18 : Universal Serial Bus + : ID_WAKEUP_F : v-ape : + : VBUS_DET_F : musb_1v8 : + : VBUS_DET_R : : + : USB_LINK_STATUS : : + : USB_ADP_PROBE_PLUG : : + : USB_ADP_PROBE_UNPLUG : : + +Required child device properties: +- compatible : "stericsson,ab8500-[bm|btemp|charger|fg|gpadc|gpio|ponkey| + pwm|regulator|rtc|sysctrl|usb]"; + +Optional child device properties: +- interrupts : contains the device IRQ(s) using the 2-cell format (see above) +- interrupt-names : contains names of IRQ resource in the order in which they were + supplied in the interrupts property +- <supply_name>-supply : contains a phandle to the regulator supply node in Device Tree + +Non-standard child device properties: + - Audio CODEC: + - stericsson,amic[1|2]-type-single-ended : Single-ended Analoge Mic (default: differential) + - stericsson,amic1a-bias-vamic2 : Analoge Mic wishes to use a non-standard Vamic + - stericsson,amic1b-bias-vamic2 : Analoge Mic wishes to use a non-standard Vamic + - stericsson,amic2-bias-vamic1 : Analoge Mic wishes to use a non-standard Vamic + - stericsson,earpeice-cmv : Earpeice voltage (only: 950 | 1100 | 1270 | 1580) + +ab8500 { + compatible = "stericsson,ab8500"; + interrupts = <0 40 0x4>; + interrupt-controller; + #interrupt-cells = <2>; + + ab8500-rtc { + compatible = "stericsson,ab8500-rtc"; + interrupts = <17 0x4 + 18 0x4>; + interrupt-names = "60S", "ALARM"; + }; + + ab8500-gpadc { + compatible = "stericsson,ab8500-gpadc"; + interrupts = <32 0x4 + 39 0x4>; + interrupt-names = "HW_CONV_END", "SW_CONV_END"; + vddadc-supply = <&ab8500_ldo_tvout_reg>; + }; + + ab8500-usb { + compatible = "stericsson,ab8500-usb"; + interrupts = < 90 0x4 + 96 0x4 + 14 0x4 + 15 0x4 + 79 0x4 + 74 0x4 + 75 0x4>; + interrupt-names = "ID_WAKEUP_R", + "ID_WAKEUP_F", + "VBUS_DET_F", + "VBUS_DET_R", + "USB_LINK_STATUS", + "USB_ADP_PROBE_PLUG", + "USB_ADP_PROBE_UNPLUG"; + vddulpivio18-supply = <&ab8500_ldo_initcore_reg>; + v-ape-supply = <&db8500_vape_reg>; + musb_1v8-supply = <&db8500_vsmps2_reg>; + }; + + ab8500-ponkey { + compatible = "stericsson,ab8500-ponkey"; + interrupts = <6 0x4 + 7 0x4>; + interrupt-names = "ONKEY_DBF", "ONKEY_DBR"; + }; + + ab8500-sysctrl { + compatible = "stericsson,ab8500-sysctrl"; + }; + + ab8500-pwm { + compatible = "stericsson,ab8500-pwm"; + }; + + codec: ab8500-codec { + compatible = "stericsson,ab8500-codec"; + + stericsson,earpeice-cmv = <950>; /* Units in mV. */ + }; + + ab8500-regulators { + compatible = "stericsson,ab8500-regulator"; + + ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { + /* + * See: Documentation/devicetree/bindings/regulator/regulator.txt + * for more information on regulators + */ + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/as3711.txt b/Documentation/devicetree/bindings/mfd/as3711.txt new file mode 100644 index 00000000..d98cf18c --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/as3711.txt @@ -0,0 +1,73 @@ +AS3711 is an I2C PMIC from Austria MicroSystems with multiple DCDC and LDO power +supplies, a battery charger and an RTC. So far only bindings for the two stepup +DCDC converters are defined. Other DCDC and LDO supplies are configured, using +standard regulator properties, they must belong to a sub-node, called +"regulators" and be called "sd1" to "sd4" and "ldo1" to "ldo8." Stepup converter +configuration should be placed in a subnode, called "backlight." + +Compulsory properties: +- compatible : must be "ams,as3711" +- reg : specifies the I2C address + +To use the SU1 converter as a backlight source the following two properties must +be provided: +- su1-dev : framebuffer phandle +- su1-max-uA : maximum current + +To use the SU2 converter as a backlight source the following two properties must +be provided: +- su2-dev : framebuffer phandle +- su1-max-uA : maximum current + +Additionally one of these properties must be provided to select the type of +feedback used: +- su2-feedback-voltage : voltage feedback is used +- su2-feedback-curr1 : CURR1 input used for current feedback +- su2-feedback-curr2 : CURR2 input used for current feedback +- su2-feedback-curr3 : CURR3 input used for current feedback +- su2-feedback-curr-auto: automatic current feedback selection + +and one of these to select the over-voltage protection pin +- su2-fbprot-lx-sd4 : LX_SD4 is used for over-voltage protection +- su2-fbprot-gpio2 : GPIO2 is used for over-voltage protection +- su2-fbprot-gpio3 : GPIO3 is used for over-voltage protection +- su2-fbprot-gpio4 : GPIO4 is used for over-voltage protection + +If "su2-feedback-curr-auto" is selected, one or more of the following properties +have to be specified: +- su2-auto-curr1 : use CURR1 input for current feedback +- su2-auto-curr2 : use CURR2 input for current feedback +- su2-auto-curr3 : use CURR3 input for current feedback + +Example: + +as3711@40 { + compatible = "ams,as3711"; + reg = <0x40>; + + regulators { + sd4 { + regulator-name = "1.215V"; + regulator-min-microvolt = <1215000>; + regulator-max-microvolt = <1235000>; + }; + ldo2 { + regulator-name = "2.8V CPU"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-boot-on; + }; + }; + + backlight { + compatible = "ams,as3711-bl"; + su2-dev = <&lcdc>; + su2-max-uA = <36000>; + su2-feedback-curr-auto; + su2-fbprot-gpio4; + su2-auto-curr1; + su2-auto-curr2; + su2-auto-curr3; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/cros-ec.txt b/Documentation/devicetree/bindings/mfd/cros-ec.txt new file mode 100644 index 00000000..e0e59c58 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/cros-ec.txt @@ -0,0 +1,56 @@ +ChromeOS Embedded Controller + +Google's ChromeOS EC is a Cortex-M device which talks to the AP and +implements various function such as keyboard and battery charging. + +The EC can be connect through various means (I2C, SPI, LPC) and the +compatible string used depends on the inteface. Each connection method has +its own driver which connects to the top level interface-agnostic EC driver. +Other Linux driver (such as cros-ec-keyb for the matrix keyboard) connect to +the top-level driver. + +Required properties (I2C): +- compatible: "google,cros-ec-i2c" +- reg: I2C slave address + +Required properties (SPI): +- compatible: "google,cros-ec-spi" +- reg: SPI chip select + +Required properties (LPC): +- compatible: "google,cros-ec-lpc" +- reg: List of (IO address, size) pairs defining the interface uses + + +Example for I2C: + +i2c@12CA0000 { + cros-ec@1e { + reg = <0x1e>; + compatible = "google,cros-ec-i2c"; + interrupts = <14 0>; + interrupt-parent = <&wakeup_eint>; + wakeup-source; + }; + + +Example for SPI: + +spi@131b0000 { + ec@0 { + compatible = "google,cros-ec-spi"; + reg = <0x0>; + interrupts = <14 0>; + interrupt-parent = <&wakeup_eint>; + wakeup-source; + spi-max-frequency = <5000000>; + controller-data { + cs-gpio = <&gpf0 3 4 3 0>; + samsung,spi-cs; + samsung,spi-feedback-delay = <2>; + }; + }; +}; + + +Example for LPC is not supplied as it is not yet implemented. diff --git a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt new file mode 100644 index 00000000..1857f4a6 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt @@ -0,0 +1,60 @@ +* Dialog DA9052/53 Power Management Integrated Circuit (PMIC) + +Required properties: +- compatible : Should be "dlg,da9052", "dlg,da9053-aa", + "dlg,da9053-ab", or "dlg,da9053-bb" + +Sub-nodes: +- regulators : Contain the regulator nodes. The DA9052/53 regulators are + bound using their names as listed below: + + buck0 : regulator BUCK0 + buck1 : regulator BUCK1 + buck2 : regulator BUCK2 + buck3 : regulator BUCK3 + ldo4 : regulator LDO4 + ldo5 : regulator LDO5 + ldo6 : regulator LDO6 + ldo7 : regulator LDO7 + ldo8 : regulator LDO8 + ldo9 : regulator LDO9 + ldo10 : regulator LDO10 + ldo11 : regulator LDO11 + ldo12 : regulator LDO12 + ldo13 : regulator LDO13 + + The bindings details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +Examples: + +i2c@63fc8000 { /* I2C1 */ + status = "okay"; + + pmic: dialog@48 { + compatible = "dlg,da9053-aa"; + reg = <0x48>; + + regulators { + buck0 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2075000>; + }; + + buck1 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2075000>; + }; + + buck2 { + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <2500000>; + }; + + buck3 { + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <2500000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt new file mode 100644 index 00000000..c6a3469d --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77686.txt @@ -0,0 +1,59 @@ +Maxim MAX77686 multi-function device + +MAX77686 is a Mulitifunction device with PMIC, RTC and Charger on chip. It is +interfaced to host controller using i2c interface. PMIC and Charger submodules +are addressed using same i2c slave address whereas RTC submodule uses +different i2c slave address,presently for which we are statically creating i2c +client while probing.This document describes the binding for mfd device and +PMIC submodule. + +Required properties: +- compatible : Must be "maxim,max77686"; +- reg : Specifies the i2c slave address of PMIC block. +- interrupts : This i2c device has an IRQ line connected to the main SoC. +- interrupt-parent : The parent interrupt controller. + +Optional node: +- voltage-regulators : The regulators of max77686 have to be instantiated + under subnode named "voltage-regulators" using the following format. + + regulator_name { + regulator-compatible = LDOn/BUCKn + standard regulator constraints.... + }; + refer Documentation/devicetree/bindings/regulator/regulator.txt + + The regulator-compatible property of regulator should initialized with string +to get matched with their hardware counterparts as follow: + + -LDOn : for LDOs, where n can lie in range 1 to 26. + example: LDO1, LDO2, LDO26. + -BUCKn : for BUCKs, where n can lie in range 1 to 9. + example: BUCK1, BUCK5, BUCK9. + +Example: + + max77686@09 { + compatible = "maxim,max77686"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + + voltage-regulators { + ldo11_reg { + regulator-compatible = "LDO11"; + regulator-name = "vdd_ldo11"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + regulator-always-on; + }; + + buck1_reg { + regulator-compatible = "BUCK1"; + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + } diff --git a/Documentation/devicetree/bindings/mfd/max8925.txt b/Documentation/devicetree/bindings/mfd/max8925.txt new file mode 100644 index 00000000..4f0dc663 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max8925.txt @@ -0,0 +1,64 @@ +* Maxim max8925 Power Management IC + +Required parent device properties: +- compatible : "maxim,max8925" +- reg : the I2C slave address for the max8925 chip +- interrupts : IRQ line for the max8925 chip +- interrupt-controller: describes the max8925 as an interrupt + controller (has its own domain) +- #interrupt-cells : should be 1. + - The cell is the max8925 local IRQ number + +Optional parent device properties: +- maxim,tsc-irq: there are 2 IRQ lines for max8925, one is indicated in + interrupts property, the other is indicated here. + +max8925 consists of a large and varied group of sub-devices: + +Device Supply Names Description +------ ------------ ----------- +max8925-onkey : : On key +max8925-rtc : : RTC +max8925-regulator : : Regulators +max8925-backlight : : Backlight +max8925-touch : : Touchscreen +max8925-power : : Charger + +Example: + + pmic: max8925@3c { + compatible = "maxim,max8925"; + reg = <0x3c>; + interrupts = <1>; + interrupt-parent = <&intcmux4>; + interrupt-controller; + #interrupt-cells = <1>; + maxim,tsc-irq = <0>; + + regulators { + SDV1 { + regulator-min-microvolt = <637500>; + regulator-max-microvolt = <1425000>; + regulator-boot-on; + regulator-always-on; + }; + + LDO1 { + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <3900000>; + regulator-boot-on; + regulator-always-on; + }; + + }; + backlight { + maxim,max8925-dual-string = <0>; + }; + charger { + batt-detect = <0>; + topoff-threshold = <1>; + fast-charge = <7>; + no-temp-support = <0>; + no-insert-detect = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt new file mode 100644 index 00000000..abd9e3cb --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -0,0 +1,108 @@ +* Freescale MC13783/MC13892 Power Management Integrated Circuit (PMIC) + +Required properties: +- compatible : Should be "fsl,mc13783" or "fsl,mc13892" + +Optional properties: +- fsl,mc13xxx-uses-adc : Indicate the ADC is being used +- fsl,mc13xxx-uses-codec : Indicate the Audio Codec is being used +- fsl,mc13xxx-uses-rtc : Indicate the RTC is being used +- fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used + +Sub-nodes: +- regulators : Contain the regulator nodes. The regulators are bound using + their names as listed below with their registers and bits for enabling. + +MC13783 regulators: + sw1a : regulator SW1A (register 24, bit 0) + sw1b : regulator SW1B (register 25, bit 0) + sw2a : regulator SW2A (register 26, bit 0) + sw2b : regulator SW2B (register 27, bit 0) + sw3 : regulator SW3 (register 29, bit 20) + vaudio : regulator VAUDIO (register 32, bit 0) + viohi : regulator VIOHI (register 32, bit 3) + violo : regulator VIOLO (register 32, bit 6) + vdig : regulator VDIG (register 32, bit 9) + vgen : regulator VGEN (register 32, bit 12) + vrfdig : regulator VRFDIG (register 32, bit 15) + vrfref : regulator VRFREF (register 32, bit 18) + vrfcp : regulator VRFCP (register 32, bit 21) + vsim : regulator VSIM (register 33, bit 0) + vesim : regulator VESIM (register 33, bit 3) + vcam : regulator VCAM (register 33, bit 6) + vrfbg : regulator VRFBG (register 33, bit 9) + vvib : regulator VVIB (register 33, bit 11) + vrf1 : regulator VRF1 (register 33, bit 12) + vrf2 : regulator VRF2 (register 33, bit 15) + vmmc1 : regulator VMMC1 (register 33, bit 18) + vmmc2 : regulator VMMC2 (register 33, bit 21) + gpo1 : regulator GPO1 (register 34, bit 6) + gpo2 : regulator GPO2 (register 34, bit 8) + gpo3 : regulator GPO3 (register 34, bit 10) + gpo4 : regulator GPO4 (register 34, bit 12) + pwgt1spi : regulator PWGT1SPI (register 34, bit 15) + pwgt2spi : regulator PWGT2SPI (register 34, bit 16) + +MC13892 regulators: + vcoincell : regulator VCOINCELL (register 13, bit 23) + sw1 : regulator SW1 (register 24, bit 0) + sw2 : regulator SW2 (register 25, bit 0) + sw3 : regulator SW3 (register 26, bit 0) + sw4 : regulator SW4 (register 27, bit 0) + swbst : regulator SWBST (register 29, bit 20) + vgen1 : regulator VGEN1 (register 32, bit 0) + viohi : regulator VIOHI (register 32, bit 3) + vdig : regulator VDIG (register 32, bit 9) + vgen2 : regulator VGEN2 (register 32, bit 12) + vpll : regulator VPLL (register 32, bit 15) + vusb2 : regulator VUSB2 (register 32, bit 18) + vgen3 : regulator VGEN3 (register 33, bit 0) + vcam : regulator VCAM (register 33, bit 6) + vvideo : regulator VVIDEO (register 33, bit 12) + vaudio : regulator VAUDIO (register 33, bit 15) + vsd : regulator VSD (register 33, bit 18) + gpo1 : regulator GPO1 (register 34, bit 6) + gpo2 : regulator GPO2 (register 34, bit 8) + gpo3 : regulator GPO3 (register 34, bit 10) + gpo4 : regulator GPO4 (register 34, bit 12) + pwgt1spi : regulator PWGT1SPI (register 34, bit 15) + pwgt2spi : regulator PWGT2SPI (register 34, bit 16) + vusb : regulator VUSB (register 50, bit 3) + + The bindings details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +Examples: + +ecspi@70010000 { /* ECSPI1 */ + fsl,spi-num-chipselects = <2>; + cs-gpios = <&gpio4 24 0>, /* GPIO4_24 */ + <&gpio4 25 0>; /* GPIO4_25 */ + status = "okay"; + + pmic: mc13892@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mc13892"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&gpio0>; + interrupts = <8>; + + regulators { + sw1_reg: mc13892__sw1 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1375000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: mc13892__sw2 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1850000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt new file mode 100644 index 00000000..b381fa69 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt @@ -0,0 +1,80 @@ +OMAP HS USB Host + +Required properties: + +- compatible: should be "ti,usbhs-host" +- reg: should contain one register range i.e. start and length +- ti,hwmods: must contain "usb_host_hs" + +Optional properties: + +- num-ports: number of USB ports. Usually this is automatically detected + from the IP's revision register but can be overridden by specifying + this property. A maximum of 3 ports are supported at the moment. + +- portN-mode: String specifying the port mode for port N, where N can be + from 1 to 3. If the port mode is not specified, that port is treated + as unused. When specified, it must be one of the following. + "ehci-phy", + "ehci-tll", + "ehci-hsic", + "ohci-phy-6pin-datse0", + "ohci-phy-6pin-dpdm", + "ohci-phy-3pin-datse0", + "ohci-phy-4pin-dpdm", + "ohci-tll-6pin-datse0", + "ohci-tll-6pin-dpdm", + "ohci-tll-3pin-datse0", + "ohci-tll-4pin-dpdm", + "ohci-tll-2pin-datse0", + "ohci-tll-2pin-dpdm", + +- single-ulpi-bypass: Must be present if the controller contains a single + ULPI bypass control bit. e.g. OMAP3 silicon <= ES2.1 + +Required properties if child node exists: + +- #address-cells: Must be 1 +- #size-cells: Must be 1 +- ranges: must be present + +Properties for children: + +The OMAP HS USB Host subsystem contains EHCI and OHCI controllers. +See Documentation/devicetree/bindings/usb/omap-ehci.txt and +omap3-ohci.txt + +Example for OMAP4: + +usbhshost: usbhshost@4a064000 { + compatible = "ti,usbhs-host"; + reg = <0x4a064000 0x800>; + ti,hwmods = "usb_host_hs"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + usbhsohci: ohci@4a064800 { + compatible = "ti,ohci-omap3", "usb-ohci"; + reg = <0x4a064800 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 76 0x4>; + }; + + usbhsehci: ehci@4a064c00 { + compatible = "ti,ehci-omap", "usb-ehci"; + reg = <0x4a064c00 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 77 0x4>; + }; +}; + +&usbhshost { + port1-mode = "ehci-phy"; + port2-mode = "ehci-tll"; + port3-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy 0 &hsusb3_phy>; +}; diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt new file mode 100644 index 00000000..62fe6972 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt @@ -0,0 +1,17 @@ +OMAP HS USB Host TLL (Transceiver-Less Interface) + +Required properties: + +- compatible : should be "ti,usbhs-tll" +- reg : should contain one register range i.e. start and length +- interrupts : should contain the TLL module's interrupt +- ti,hwmod : must contain "usb_tll_hs" + +Example: + + usbhstll: usbhstll@4a062000 { + compatible = "ti,usbhs-tll"; + reg = <0x4a062000 0x1000>; + interrupts = <78>; + ti,hwmods = "usb_tll_hs"; + }; diff --git a/Documentation/devicetree/bindings/mfd/rt8973.txt b/Documentation/devicetree/bindings/mfd/rt8973.txt new file mode 100644 index 00000000..71957c60 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/rt8973.txt @@ -0,0 +1,24 @@ +Richtek RT8973 MUIC + +Required properties: + + - compatible : should be "richtek,rt8973" + - reg : i2c slave address of the device + - interrupt-parent : parent of interrupt + - interrupts : interrupt to indicate accessories attach or detach + - rt8973,irq-gpio : irq gpio + + + +Example: + &soc { + + i2c_0: i2c@f9967000 { + rt8973@14 { + compatible = "richtek,rt8973"; + reg = <0x14>; + interrupt-parent = <&msmgpio>; + rt8973,irq-gpio = <&msmgpio 73 0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt new file mode 100644 index 00000000..56edb552 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -0,0 +1,28 @@ +* ST Microelectronics STMPE Multi-Functional Device + +STMPE is an MFD device which may expose the following inbuilt devices: gpio, +keypad, touchscreen, adc, pwm, rotator. + +Required properties: + - compatible : "st,stmpe[610|801|811|1601|2401|2403]" + - reg : I2C/SPI address of the device + +Optional properties: + - interrupts : The interrupt outputs from the controller + - interrupt-controller : Marks the device node as an interrupt controller + - interrupt-parent : Specifies which IRQ controller we're connected to + - wakeup-source : Marks the input device as wakable + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 + +Example: + + stmpe1601: stmpe1601@40 { + compatible = "st,stmpe1601"; + reg = <0x40>; + interrupts = <26 0x4>; + interrupt-parent = <&gpio6>; + interrupt-controller; + + wakeup-source; + st,autosleep-timeout = <1024>; + }; diff --git a/Documentation/devicetree/bindings/mfd/syscon.txt b/Documentation/devicetree/bindings/mfd/syscon.txt new file mode 100644 index 00000000..fe8150bb --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/syscon.txt @@ -0,0 +1,20 @@ +* System Controller Registers R/W driver + +System controller node represents a register region containing a set +of miscellaneous registers. The registers are not cohesive enough to +represent as any specific type of device. The typical use-case is for +some other node's driver, or platform-specific code, to acquire a +reference to the syscon node (e.g. by phandle, node path, or search +using a specific compatible value), interrogate the node (or associated +OS driver) to determine the location of the registers, and access the +registers directly. + +Required properties: +- compatible: Should contain "syscon". +- reg: the register region can be accessed from syscon + +Examples: +gpr: iomuxc-gpr@020e0000 { + compatible = "fsl,imx6q-iomuxc-gpr", "syscon"; + reg = <0x020e0000 0x38>; +}; diff --git a/Documentation/devicetree/bindings/mfd/tps6507x.txt b/Documentation/devicetree/bindings/mfd/tps6507x.txt new file mode 100755 index 00000000..8fffa3c5 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps6507x.txt @@ -0,0 +1,91 @@ +TPS6507x Power Management Integrated Circuit + +Required properties: +- compatible: "ti,tps6507x" +- reg: I2C slave address +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the + given device need to be present. The definition for each of these nodes + is defined using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + The regulator is matched with the regulator-compatible. + + The valid regulator-compatible values are: + tps6507x: vdcdc1, vdcdc2, vdcdc3, vldo1, vldo2 +- xxx-supply: Input voltage supply regulator. + These entries are required if regulators are enabled for a device. + Missing of these properties can cause the regulator registration + fails. + If some of input supply is powered through battery or always-on + supply then also it is require to have these parameters with proper + node handle of always on power supply. + tps6507x: + vindcdc1_2-supply: VDCDC1 and VDCDC2 input. + vindcdc3-supply : VDCDC3 input. + vldo1_2-supply : VLDO1 and VLDO2 input. + +Regulator Optional properties: +- defdcdc_default: It's property of DCDC2 and DCDC3 regulators. + 0: If defdcdc pin of DCDC2/DCDC3 is pulled to GND. + 1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH. + If this property is not defined, it defaults to 0 (not enabled). + +Example: + + pmu: tps6507x@48 { + compatible = "ti,tps6507x"; + reg = <0x48>; + + vindcdc1_2-supply = <&vbat>; + vindcdc3-supply = <...>; + vinldo1_2-supply = <...>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + vdcdc1_reg: regulator@0 { + regulator-compatible = "VDCDC1"; + reg = <0>; + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3450000>; + regulator-always-on; + regulator-boot-on; + }; + vdcdc2_reg: regulator@1 { + regulator-compatible = "VDCDC2"; + reg = <1>; + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <3450000>; + regulator-always-on; + regulator-boot-on; + defdcdc_default = <1>; + }; + vdcdc3_reg: regulator@2 { + regulator-compatible = "VDCDC3"; + reg = <2>; + regulator-min-microvolt = <950000> + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + defdcdc_default = <1>; + }; + ldo1_reg: regulator@3 { + regulator-compatible = "LDO1"; + reg = <3>; + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <1890000>; + regulator-always-on; + regulator-boot-on; + }; + ldo2_reg: regulator@4 { + regulator-compatible = "LDO2"; + reg = <4>; + regulator-min-microvolt = <1140000>; + regulator-max-microvolt = <1320000>; + regulator-always-on; + regulator-boot-on; + }; + }; + + }; diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt new file mode 100644 index 00000000..2e330488 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -0,0 +1,201 @@ +TPS65910 Power Management Integrated Circuit + +Required properties: +- compatible: "ti,tps65910" or "ti,tps65911" +- reg: I2C slave address +- interrupts: the interrupt outputs of the controller +- #gpio-cells: number of cells to describe a GPIO, this should be 2. + The first cell is the GPIO number. + The second cell is used to specify additional options <unused>. +- gpio-controller: mark the device as a GPIO controller +- #interrupt-cells: the number of cells to describe an IRQ, this should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupts.txt +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the given + device need to be present. The definition for each of these nodes is defined + using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + The regulator is matched with the regulator-compatible. + + The valid regulator-compatible values are: + tps65910: vrtc, vio, vdd1, vdd2, vdd3, vdig1, vdig2, vpll, vdac, vaux1, + vaux2, vaux33, vmmc + tps65911: vrtc, vio, vdd1, vdd3, vddctrl, ldo1, ldo2, ldo3, ldo4, ldo5, + ldo6, ldo7, ldo8 + +- xxx-supply: Input voltage supply regulator. + These entries are require if regulators are enabled for a device. Missing of these + properties can cause the regulator registration fails. + If some of input supply is powered through battery or always-on supply then + also it is require to have these parameters with proper node handle of always + on power supply. + tps65910: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: VAUX33 and VMMC input. + vcc4-supply: VAUX1 and VAUX2 input. + vcc5-supply: VPLL and VDAC input. + vcc6-supply: VDIG1 and VDIG2 input. + vcc7-supply: VRTC input. + vccio-supply: VIO input. + tps65911: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: LDO6, LDO7 and LDO8 input. + vcc4-supply: LDO5 input. + vcc5-supply: LDO3 and LDO4 input. + vcc6-supply: LDO1 and LDO2 input. + vcc7-supply: VRTC input. + vccio-supply: VIO input. + +Optional properties: +- ti,vmbch-threshold: (tps65911) main battery charged threshold + comparator. (see VMBCH_VSEL in TPS65910 datasheet) +- ti,vmbch2-threshold: (tps65911) main battery discharged threshold + comparator. (see VMBCH_VSEL in TPS65910 datasheet) +- ti,en-ck32k-xtal: enable external 32-kHz crystal oscillator (see CK32K_CTRL + in TPS6591X datasheet) +- ti,en-gpio-sleep: enable sleep control for gpios + There should be 9 entries here, one for each gpio. +- ti,system-power-controller: Telling whether or not this pmic is controlling + the system power. + +Regulator Optional properties: +- ti,regulator-ext-sleep-control: enable external sleep + control through external inputs [0 (not enabled), 1 (EN1), 2 (EN2) or 4(EN3)] + If this property is not defined, it defaults to 0 (not enabled). + +Example: + + pmu: tps65910@d2 { + compatible = "ti,tps65910"; + reg = <0xd2>; + interrupt-parent = <&intc>; + interrupts = < 0 118 0x04 >; + + #gpio-cells = <2>; + gpio-controller; + + #interrupt-cells = <2>; + interrupt-controller; + + ti,system-power-controller; + + ti,vmbch-threshold = 0; + ti,vmbch2-threshold = 0; + ti,en-ck32k-xtal; + ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>; + + vcc1-supply = <®_parent>; + vcc2-supply = <&some_reg>; + vcc3-supply = <...>; + vcc4-supply = <...>; + vcc5-supply = <...>; + vcc6-supply = <...>; + vcc7-supply = <...>; + vccio-supply = <...>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + vdd1_reg: regulator@0 { + regulator-compatible = "vdd1"; + reg = <0>; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <0>; + }; + vdd2_reg: regulator@1 { + regulator-compatible = "vdd2"; + reg = <1>; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <4>; + }; + vddctrl_reg: regulator@2 { + regulator-compatible = "vddctrl"; + reg = <2>; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <0>; + }; + vio_reg: regulator@3 { + regulator-compatible = "vio"; + reg = <3>; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <1>; + }; + ldo1_reg: regulator@4 { + regulator-compatible = "ldo1"; + reg = <4>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo2_reg: regulator@5 { + regulator-compatible = "ldo2"; + reg = <5>; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo3_reg: regulator@6 { + regulator-compatible = "ldo3"; + reg = <6>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo4_reg: regulator@7 { + regulator-compatible = "ldo4"; + reg = <7>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + ti,regulator-ext-sleep-control = <0>; + }; + ldo5_reg: regulator@8 { + regulator-compatible = "ldo5"; + reg = <8>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo6_reg: regulator@9 { + regulator-compatible = "ldo6"; + reg = <9>; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo7_reg: regulator@10 { + regulator-compatible = "ldo7"; + reg = <10>; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <1>; + }; + ldo8_reg: regulator@11 { + regulator-compatible = "ldo8"; + reg = <11>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + ti,regulator-ext-sleep-control = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/twl-familly.txt b/Documentation/devicetree/bindings/mfd/twl-familly.txt new file mode 100644 index 00000000..a66fcf94 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl-familly.txt @@ -0,0 +1,47 @@ +Texas Instruments TWL family + +The TWLs are Integrated Power Management Chips. +Some version might contain much more analog function like +USB transceiver or Audio amplifier. +These chips are connected to an i2c bus. + + +Required properties: +- compatible : Must be "ti,twl4030"; + For Integrated power-management/audio CODEC device used in OMAP3 + based boards +- compatible : Must be "ti,twl6030"; + For Integrated power-management used in OMAP4 based boards +- interrupts : This i2c device has an IRQ line connected to the main SoC +- interrupt-controller : Since the twl support several interrupts internally, + it is considered as an interrupt controller cascaded to the SoC one. +- #interrupt-cells = <1>; +- interrupt-parent : The parent interrupt controller. + +Optional node: +- Child nodes contain in the twl. The twl family is made of several variants + that support a different number of features. + The children nodes will thus depend of the capability of the variant. + + +Example: +/* + * Integrated Power Management Chip + * http://www.ti.com/lit/ds/symlink/twl6030.pdf + */ +twl@48 { + compatible = "ti,twl6030"; + reg = <0x48>; + interrupts = <39>; /* IRQ_SYS_1N cascaded to gic */ + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + #address-cells = <1>; + #size-cells = <0>; + + twl_rtc { + compatible = "ti,twl_rtc"; + interrupts = <11>; + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/twl4030-audio.txt b/Documentation/devicetree/bindings/mfd/twl4030-audio.txt new file mode 100644 index 00000000..414d2ae0 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl4030-audio.txt @@ -0,0 +1,46 @@ +Texas Instruments TWL family (twl4030) audio module + +The audio module inside the TWL family consist of an audio codec and a vibra +driver. + +Required properties: +- compatible : must be "ti,twl4030-audio" + +Optional properties, nodes: + +Audio functionality: +- codec { }: Need to be present if the audio functionality is used. Within this + section the following options can be used: +- ti,digimic_delay: Delay need after enabling the digimic to reduce artifacts + from the start of the recorded sample (in ms) +-ti,ramp_delay_value: HS ramp delay configuration to reduce pop noise +-ti,hs_extmute: Use external mute for HS pop reduction +-ti,hs_extmute_gpio: Use external GPIO to control the external mute +-ti,offset_cncl_path: Offset cancellation path selection, refer to TRM for the + valid values. + +Vibra functionality +- ti,enable-vibra: Need to be set to <1> if the vibra functionality is used. if + missing or it is 0, the vibra functionality is disabled. + +Example: +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + + ti,enable-vibra = <1>; + + codec { + ti,ramp_delay_value = <3>; + }; + + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/twl6040.txt b/Documentation/devicetree/bindings/mfd/twl6040.txt new file mode 100644 index 00000000..0f5dd709 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl6040.txt @@ -0,0 +1,65 @@ +Texas Instruments TWL6040 family + +The TWL6040s are 8-channel high quality low-power audio codecs providing audio, +vibra and GPO functionality on OMAP4+ platforms. +They are connected ot the host processor via i2c for commands, McPDM for audio +data and commands. + +Required properties: +- compatible : "ti,twl6040" for twl6040, "ti,twl6041" for twl6041 +- reg: must be 0x4b for i2c address +- interrupts: twl6040 has one interrupt line connecteded to the main SoC +- interrupt-parent: The parent interrupt controller +- gpio-controller: +- #gpio-cells = <1>: twl6040 provides GPO lines. +- twl6040,audpwron-gpio: Power on GPIO line for the twl6040 + +- vio-supply: Regulator for the twl6040 VIO supply +- v2v1-supply: Regulator for the twl6040 V2V1 supply + +Optional properties, nodes: +- enable-active-high: To power on the twl6040 during boot. + +Vibra functionality +Required properties: +- vddvibl-supply: Regulator for the left vibra motor +- vddvibr-supply: Regulator for the right vibra motor +- vibra { }: Configuration section for vibra parameters containing the following + properties: +- ti,vibldrv-res: Resistance parameter for left driver +- ti,vibrdrv-res: Resistance parameter for right driver +- ti,viblmotor-res: Resistance parameter for left motor +- ti,viblmotor-res: Resistance parameter for right motor + +Optional properties within vibra { } section: +- vddvibl_uV: If the vddvibl default voltage need to be changed +- vddvibr_uV: If the vddvibr default voltage need to be changed + +Example: +&i2c1 { + twl6040: twl@4b { + compatible = "ti,twl6040"; + + interrupts = <0 119 4>; + interrupt-parent = <&gic>; + twl6040,audpwron-gpio = <&gpio4 31 0>; + + vio-supply = <&v1v8>; + v2v1-supply = <&v2v1>; + enable-active-high; + + /* regulators for vibra motor */ + vddvibl-supply = <&vbat>; + vddvibr-supply = <&vbat>; + + vibra { + /* Vibra driver, motor resistance parameters */ + ti,vibldrv-res = <8>; + ti,vibrdrv-res = <3>; + ti,viblmotor-res = <10>; + ti,vibrmotor-res = <10>; + }; + }; +}; + +/include/ "twl6040.dtsi" diff --git a/Documentation/devicetree/bindings/mfd/vexpress-spc.txt b/Documentation/devicetree/bindings/mfd/vexpress-spc.txt new file mode 100644 index 00000000..1d71dc2f --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/vexpress-spc.txt @@ -0,0 +1,35 @@ +* ARM Versatile Express Serial Power Controller device tree bindings + +Latest ARM development boards implement a power management interface (serial +power controller - SPC) that is capable of managing power/voltage and +operating point transitions, through memory mapped registers interface. + +On testchips like TC2 it also provides a configuration interface that can +be used to read/write values which cannot be read/written through simple +memory mapped reads/writes. + +- spc node + + - compatible: + Usage: required + Value type: <stringlist> + Definition: must be + "arm,vexpress-spc,v2p-ca15_a7","arm,vexpress-spc" + - reg: + Usage: required + Value type: <prop-encode-array> + Definition: A standard property that specifies the base address + and the size of the SPC address space + - interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: SPC interrupt configuration. A standard property + that follows ePAPR interrupts specifications + +Example: + +spc: spc@7fff0000 { + compatible = "arm,vexpress-spc,v2p-ca15_a7","arm,vexpress-spc"; + reg = <0 0x7FFF0000 0 0x1000>; + interrupts = <0 95 4>; +}; |