Initial file dump from open source releaseHEADmaster

1 files changed, 180 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
new file mode 100644
index 00000000..b275be49
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
@@ -0,0 +1,180 @@
+== Introduction ==
+
+Hardware modules that control pin multiplexing or configuration parameters
+such as pull-up/down, tri-state, drive-strength etc are designated as pin
+controllers. Each pin controller must be represented as a node in device tree,
+just like any other hardware module.
+
+Hardware modules whose signals are affected by pin configuration are
+designated client devices. Again, each client device must be represented as a
+node in device tree, just like any other hardware module.
+
+For a client device to operate correctly, certain pin controllers must
+set up certain specific pin configurations. Some client devices need a
+single static pin configuration, e.g. set up during initialization. Others
+need to reconfigure pins at run-time, for example to tri-state pins when the
+device is inactive. Hence, each client device can define a set of named
+states. The number and names of those states is defined by the client device's
+own binding.
+
+The common pinctrl bindings defined in this file provide an infrastructure
+for client device device tree nodes to map those state names to the pin
+configuration used by those states.
+
+Note that pin controllers themselves may also be client devices of themselves.
+For example, a pin controller may set up its own "active" state when the
+driver loads. This would allow representing a board's static pin configuration
+in a single place, rather than splitting it across multiple client device
+nodes. The decision to do this or not somewhat rests with the author of
+individual board device tree files, and any requirements imposed by the
+bindings for the individual client devices in use by that board, i.e. whether
+they require certain specific named states for dynamic pin configuration.
+
+== Pinctrl client devices ==
+
+For each client device individually, every pin state is assigned an integer
+ID. These numbers start at 0, and are contiguous. For each state ID, a unique
+property exists to define the pin configuration. Each state may also be
+assigned a name. When names are used, another property exists to map from
+those names to the integer IDs.
+
+Each client device's own binding determines the set of states the must be
+defined in its device tree node, and whether to define the set of state
+IDs that must be provided, or whether to define the set of state names that
+must be provided.
+
+Required properties:
+pinctrl-0:	List of phandles, each pointing at a pin configuration
+		node. These referenced pin configuration nodes must be child
+		nodes of the pin controller that they configure. Multiple
+		entries may exist in this list so that multiple pin
+		controllers may be configured, or so that a state may be built
+		from multiple nodes for a single pin controller, each
+		contributing part of the overall configuration. See the next
+		section of this document for details of the format of these
+		pin configuration nodes.
+
+		In some cases, it may be useful to define a state, but for it
+		to be empty. This may be required when a common IP block is
+		used in an SoC either without a pin controller, or where the
+		pin controller does not affect the HW module in question. If
+		the binding for that IP block requires certain pin states to
+		exist, they must still be defined, but may be left empty.
+
+Optional properties:
+pinctrl-1:	List of phandles, each pointing at a pin configuration
+		node within a pin controller.
+...
+pinctrl-n:	List of phandles, each pointing at a pin configuration
+		node within a pin controller.
+pinctrl-names:	The list of names to assign states. List entry 0 defines the
+		name for integer state ID 0, list entry 1 for state ID 1, and
+		so on.
+
+For example:
+
+	/* For a client device requiring named states */
+	device {
+		pinctrl-names = "active", "idle";
+		pinctrl-0 = <&state_0_node_a>;
+		pinctrl-1 = <&state_1_node_a &state_1_node_b>;
+	};
+
+	/* For the same device if using state IDs */
+	device {
+		pinctrl-0 = <&state_0_node_a>;
+		pinctrl-1 = <&state_1_node_a &state_1_node_b>;
+	};
+
+	/*
+	 * For an IP block whose binding supports pin configuration,
+	 * but in use on an SoC that doesn't have any pin control hardware
+	 */
+	device {
+		pinctrl-names = "active", "idle";
+		pinctrl-0 = <>;
+		pinctrl-1 = <>;
+	};
+
+== Pin controller devices ==
+
+Pin controller devices should contain the pin configuration nodes that client
+devices reference.
+
+For example:
+
+	pincontroller {
+		... /* Standard DT properties for the device itself elided */
+
+		state_0_node_a {
+			...
+		};
+		state_1_node_a {
+			...
+		};
+		state_1_node_b {
+			...
+		};
+	}
+
+The contents of each of those pin configuration child nodes is defined
+entirely by the binding for the individual pin controller device. There
+exists no common standard for this content.
+
+The pin configuration nodes need not be direct children of the pin controller
+device; they may be grandchildren, for example. Whether this is legal, and
+whether there is any interaction between the child and intermediate parent
+nodes, is again defined entirely by the binding for the individual pin
+controller device.
+
+== Using generic pinconfig options ==
+
+Generic pinconfig parameters can be used by defining a separate node containing
+the applicable parameters (and optional values), like:
+
+pcfg_pull_up: pcfg_pull_up {
+	bias-pull-up;
+	drive-strength = <20>;
+};
+
+This node should then be referenced in the appropriate pinctrl node as a phandle
+and parsed in the driver using the pinconf_generic_parse_dt_config function.
+
+Supported configuration parameters are:
+
+bias-disable		- disable any pin bias
+bias-high-impedance	- high impedance mode ("third-state", "floating")
+bias-bus-hold		- latch weakly
+bias-pull-up		- pull up the pin
+bias-pull-down		- pull down the pin
+bias-pull-pin-default	- use pin-default pull state
+drive-push-pull		- drive actively high and low
+drive-open-drain	- drive with open drain
+drive-open-source	- drive with open source
+drive-strength		- sink or source at most X mA
+input-enable		- enable input on pin (no effect on output)
+input-disable		- disable input on pin (no effect on output)
+input-schmitt-enable	- enable schmitt-trigger mode
+input-schmitt-disable	- disable schmitt-trigger mode
+input-debounce		- debounce mode with debound time X
+low-power-enable	- enable low power mode
+low-power-disable	- disable low power mode
+output-low		- set the pin to output mode with low level
+output-high		- set the pin to output mode with high level
+slew-rate		- set the slew rate
+
+Arguments for parameters:
+
+- bias-pull-up, -down and -pin-default take as optional argument 0 to disable
+  the pull, on hardware supporting it the pull strength in Ohm. bias-disable
+  will also disable any active pull.
+
+- drive-strength takes as argument the target strength in mA.
+
+- input-debounce takes the debounce time in usec as argument
+  or 0 to disable debouncing
+
+All parameters not listed here, do not take an argument.
+
+More in-depth documentation on these parameters can be found in
+<include/linux/pinctrl/pinconfig-generic.h>