Initial file dump from open source releaseHEADmaster

23 files changed, 766 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
new file mode 100644
index 00000000..0a85c70c
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
@@ -0,0 +1,68 @@
+* Atmel High Speed MultiMedia Card Interface
+
+This controller on atmel products provides an interface for MMC, SD and SDIO
+types of memory cards.
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the atmel-mci driver.
+
+1) MCI node
+
+Required properties:
+- compatible: should be "atmel,hsmci"
+- #address-cells: should be one. The cell is the slot id.
+- #size-cells: should be zero.
+- at least one slot node
+
+The node contains child nodes for each slot that the platform uses
+
+Example MCI node:
+
+mmc0: mmc@f0008000 {
+	compatible = "atmel,hsmci";
+	reg = <0xf0008000 0x600>;
+	interrupts = <12 4>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	[ child node definitions...]
+};
+
+2) slot nodes
+
+Required properties:
+- reg: should contain the slot id.
+- bus-width: number of data lines connected to the controller
+
+Optional properties:
+- cd-gpios: specify GPIOs for card detection
+- cd-inverted: invert the value of external card detect gpio line
+- wp-gpios: specify GPIOs for write protection
+
+Example slot node:
+
+slot@0 {
+	reg = <0>;
+	bus-width = <4>;
+	cd-gpios = <&pioD 15 0>
+	cd-inverted;
+};
+
+Example full MCI node:
+mmc0: mmc@f0008000 {
+	compatible = "atmel,hsmci";
+	reg = <0xf0008000 0x600>;
+	interrupts = <12 4>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	slot@0 {
+		reg = <0>;
+		bus-width = <4>;
+		cd-gpios = <&pioD 15 0>
+		cd-inverted;
+	};
+	slot@1 {
+		reg = <1>;
+		bus-width = <4>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt
new file mode 100644
index 00000000..59476fbd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt
@@ -0,0 +1,18 @@
+Broadcom BCM2835 SDHCI controller
+
+This file documents differences between the core properties described
+by mmc.txt and the properties that represent the BCM2835 controller.
+
+Required properties:
+- compatible : Should be "brcm,bcm2835-sdhci".
+- clocks : The clock feeding the SDHCI controller.
+
+Example:
+
+sdhci: sdhci {
+	compatible = "brcm,bcm2835-sdhci";
+	reg = <0x7e300000 0x100>;
+	interrupts = <2 30>;
+	clocks = <&clk_mmc>;
+	bus-width = <4>;
+};
diff --git a/Documentation/devicetree/bindings/mmc/davinci_mmc.txt b/Documentation/devicetree/bindings/mmc/davinci_mmc.txt
new file mode 100644
index 00000000..e5a0140b
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/davinci_mmc.txt
@@ -0,0 +1,33 @@
+* TI Highspeed MMC host controller for DaVinci
+
+The Highspeed MMC Host Controller on TI DaVinci family
+provides an interface for MMC, SD and SDIO types of memory cards.
+
+This file documents the properties used by the davinci_mmc driver.
+
+Required properties:
+- compatible:
+ Should be "ti,da830-mmc": for da830, da850, dm365
+ Should be "ti,dm355-mmc": for dm355, dm644x
+
+Optional properties:
+- bus-width: Number of data lines, can be <1>, <4>, or <8>, default <1>
+- max-frequency: Maximum operating clock frequency, default 25MHz.
+- dmas: List of DMA specifiers with the controller specific format
+	as described in the generic DMA client binding. A tx and rx
+	specifier is required.
+- dma-names: RX and TX  DMA request names. These strings correspond
+	1:1 with the DMA specifiers listed in dmas.
+
+Example:
+mmc0: mmc@1c40000 {
+	compatible = "ti,da830-mmc",
+	reg = <0x40000 0x1000>;
+	interrupts = <16>;
+	status = "okay";
+	bus-width = <4>;
+	max-frequency = <50000000>;
+	dmas = <&edma 16
+		&edma 17>;
+	dma-names = "rx", "tx";
+};
diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
new file mode 100644
index 00000000..6d1c0988
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
@@ -0,0 +1,87 @@
+* Samsung Exynos specific extensions to the Synopsis Designware Mobile
+  Storage Host Controller
+
+The Synopsis designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core Synopsis dw mshc controller properties described
+by synopsis-dw-mshc.txt and the properties used by the Samsung Exynos specific
+extensions to the Synopsis Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be
+	- "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210
+	  specific extensions.
+	- "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412
+	  specific extensions.
+	- "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250
+	  specific extensions.
+
+* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface
+  unit (ciu) clock. This property is applicable only for Exynos5 SoC's and
+  ignored for Exynos4 SoC's. The valid range of divider value is 0 to 7.
+
+* samsung,dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value
+  in transmit mode and CIU clock phase shift value in receive mode for single
+  data rate mode operation. Refer notes below for the order of the cells and the
+  valid values.
+
+* samsung,dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift value
+  in transmit mode and CIU clock phase shift value in receive mode for double
+  data rate mode operation. Refer notes below for the order of the cells and the
+  valid values.
+
+  Notes for the sdr-timing and ddr-timing values:
+
+    The order of the cells should be
+      - First Cell: CIU clock phase shift value for tx mode.
+      - Second Cell: CIU clock phase shift value for rx mode.
+
+    Valid values for SDR and DDR CIU clock timing for Exynos5250:
+      - valid value for tx phase shift and rx phase shift is 0 to 7.
+      - when CIU clock divider value is set to 3, all possible 8 phase shift
+        values can be used.
+      - if CIU clock divider value is 0 (that is divide by 1), both tx and rx
+        phase shift clocks should be 0.
+
+Required properties for a slot:
+
+* gpios: specifies a list of gpios used for command, clock and data bus. The
+  first gpio is the command line and the second gpio is the clock line. The
+  rest of the gpios (depending on the bus-width property) are the data lines in
+  no particular order. The format of the gpio specifier depends on the gpio
+  controller.
+
+Example:
+
+  The MSHC controller node can be split into two portions, SoC specific and
+  board specific portions as listed below.
+
+	dwmmc0@12200000 {
+		compatible = "samsung,exynos5250-dw-mshc";
+		reg = <0x12200000 0x1000>;
+		interrupts = <0 75 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	dwmmc0@12200000 {
+		num-slots = <1>;
+		supports-highspeed;
+		broken-cd;
+		fifo-depth = <0x80>;
+		card-detect-delay = <200>;
+		samsung,dw-mshc-ciu-div = <3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
+
+		slot@0 {
+			reg = <0>;
+			bus-width = <8>;
+			gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
+				<&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
+				<&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
+				<&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
+				<&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
new file mode 100644
index 00000000..bd9be0b5
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
@@ -0,0 +1,32 @@
+* Freescale Enhanced Secure Digital Host Controller (eSDHC)
+
+The Enhanced Secure Digital Host Controller provides an interface
+for MMC, SD, and SDIO types of memory cards.
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the sdhci-esdhc driver.
+
+Required properties:
+  - interrupt-parent : interrupt source phandle.
+  - clock-frequency : specifies eSDHC base clock frequency.
+
+Optional properties:
+  - sdhci,wp-inverted : specifies that eSDHC controller reports
+    inverted write-protect state; New devices should use the generic
+    "wp-inverted" property.
+  - sdhci,1-bit-only : specifies that a controller can only handle
+    1-bit data transfers. New devices should use the generic
+    "bus-width = <1>" property.
+  - sdhci,auto-cmd12: specifies that a controller can only handle auto
+    CMD12.
+
+Example:
+
+sdhci@2e000 {
+	compatible = "fsl,mpc8378-esdhc", "fsl,esdhc";
+	reg = <0x2e000 0x1000>;
+	interrupts = <42 0x8>;
+	interrupt-parent = <&ipic>;
+	/* Filled in by U-Boot */
+	clock-frequency = <0>;
+};
diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
new file mode 100644
index 00000000..1dd62254
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
@@ -0,0 +1,32 @@
+* Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX
+
+The Enhanced Secure Digital Host Controller on Freescale i.MX family
+provides an interface for MMC, SD, and SDIO types of memory cards.
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the sdhci-esdhc-imx driver.
+
+Required properties:
+- compatible : Should be "fsl,<chip>-esdhc"
+
+Optional properties:
+- fsl,cd-controller : Indicate to use controller internal card detection
+- fsl,wp-controller : Indicate to use controller internal write protection
+
+Examples:
+
+esdhc@70004000 {
+	compatible = "fsl,imx51-esdhc";
+	reg = <0x70004000 0x4000>;
+	interrupts = <1>;
+	fsl,cd-controller;
+	fsl,wp-controller;
+};
+
+esdhc@70008000 {
+	compatible = "fsl,imx51-esdhc";
+	reg = <0x70008000 0x4000>;
+	interrupts = <2>;
+	cd-gpios = <&gpio1 6 0>; /* GPIO1_6 */
+	wp-gpios = <&gpio1 5 0>; /* GPIO1_5 */
+};
diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt
new file mode 100644
index 00000000..db442355
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt
@@ -0,0 +1,24 @@
+* Freescale Secure Digital Host Controller for i.MX2/3 series
+
+This file documents differences to the properties defined in mmc.txt.
+
+Required properties:
+- compatible : Should be "fsl,<chip>-mmc", chip can be imx21 or imx31
+
+Optional properties:
+- dmas: One DMA phandle with arguments as defined by the devicetree bindings
+	of the used DMA controller.
+- dma-names: Has to be "rx-tx".
+
+Example:
+
+sdhci1: sdhci@10014000 {
+	compatible = "fsl,imx27-mmc", "fsl,imx21-mmc";
+	reg = <0x10014000 0x1000>;
+	interrupts = <11>;
+	dmas = <&dma 7>;
+	dma-names = "rx-tx";
+	bus-width = <4>;
+	cd-gpios = <&gpio3 29>;
+	status = "okay";
+};
diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
new file mode 100644
index 00000000..0e5e2ec4
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
@@ -0,0 +1,31 @@
+MMC/SD/SDIO slot directly connected to a SPI bus
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the mmc_spi driver.
+
+Required properties:
+- spi-max-frequency : maximum frequency for this device (Hz).
+- voltage-ranges : two cells are required, first cell specifies minimum
+  slot voltage (mV), second cell specifies maximum slot voltage (mV).
+  Several ranges could be specified.
+
+Optional properties:
+- gpios : may specify GPIOs in this order: Card-Detect GPIO,
+  Write-Protect GPIO. Note that this does not follow the
+  binding from mmc.txt, for historical reasons.
+- interrupt-parent : the phandle for the interrupt controller that
+  services interrupts for this device.
+
+Example:
+
+	mmc-slot@0 {
+		compatible = "fsl,mpc8323rdb-mmc-slot",
+			     "mmc-spi-slot";
+		reg = <0>;
+		gpios = <&qe_pio_d 14 1
+			 &qe_pio_d 15 0>;
+		voltage-ranges = <3300 3300>;
+		spi-max-frequency = <50000000>;
+		interrupts = <42>;
+		interrupt-parent = <&PIC>;
+	};
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
new file mode 100644
index 00000000..85aada22
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -0,0 +1,66 @@
+These properties are common to multiple MMC host controllers. Any host
+that requires the respective functionality should implement them using
+these definitions.
+
+Interpreted by the OF core:
+- reg: Registers location and length.
+- interrupts: Interrupts used by the MMC controller.
+
+Card detection:
+If no property below is supplied, host native card detect is used.
+Only one of the properties in this section should be supplied:
+  - broken-cd: There is no card detection available; polling must be used.
+  - cd-gpios: Specify GPIOs for card detection, see gpio binding
+  - non-removable: non-removable slot (like eMMC); assume always present.
+
+Optional properties:
+- bus-width: Number of data lines, can be <1>, <4>, or <8>.  The default
+  will be <1> if the property is absent.
+- wp-gpios: Specify GPIOs for write protection, see gpio binding
+- cd-inverted: when present, polarity on the CD line is inverted. See the note
+  below for the case, when a GPIO is used for the CD line
+- wp-inverted: when present, polarity on the WP line is inverted. See the note
+  below for the case, when a GPIO is used for the WP line
+- max-frequency: maximum operating clock frequency
+- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on
+  this system, even if the controller claims it is.
+- cap-sd-highspeed: SD high-speed timing is supported
+- cap-mmc-highspeed: MMC high-speed timing is supported
+- cap-power-off-card: powering off the card is safe
+- cap-sdio-irq: enable SDIO IRQ signalling on this interface
+
+*NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
+polarity properties, we have to fix the meaning of the "normal" and "inverted"
+line levels. We choose to follow the SDHCI standard, which specifies both those
+lines as "active low." Therefore, using the "cd-inverted" property means, that
+the CD line is active high, i.e. it is high, when a card is inserted. Similar
+logic applies to the "wp-inverted" property.
+
+CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs,
+specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of
+dedicated pins can be specified, using *-inverted properties. GPIO polarity can
+also be specified using the OF_GPIO_ACTIVE_LOW flag. This creates an ambiguity
+in the latter case. We choose to use the XOR logic for GPIO CD and WP lines.
+This means, the two properties are "superimposed," for example leaving the
+OF_GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted
+property results in a double-inversion and actually means the "normal" line
+polarity is in effect.
+
+Optional SDIO properties:
+- keep-power-in-suspend: Preserves card power during a suspend/resume cycle
+- enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion
+
+Example:
+
+sdhci@ab000000 {
+	compatible = "sdhci";
+	reg = <0xab000000 0x200>;
+	interrupts = <23>;
+	bus-width = <4>;
+	cd-gpios = <&gpio 69 0>;
+	cd-inverted;
+	wp-gpios = <&gpio 70 0>;
+	max-frequency = <50000000>;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
+}
diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt
new file mode 100644
index 00000000..2b584cae
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/mmci.txt
@@ -0,0 +1,15 @@
+* ARM PrimeCell MultiMedia Card Interface (MMCI) PL180/1
+
+The ARM PrimeCell MMCI PL180 and PL181 provides an interface for
+reading and writing to MultiMedia and SD cards alike.
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the mmci driver.
+
+Required properties:
+- compatible             : contains "arm,pl18x", "arm,primecell".
+- arm,primecell-periphid : contains the PrimeCell Peripheral ID.
+
+Optional properties:
+- mmc-cap-mmc-highspeed  : indicates whether MMC is high speed capable
+- mmc-cap-sd-highspeed   : indicates whether SD is high speed capable
diff --git a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt
new file mode 100644
index 00000000..515addc2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt
@@ -0,0 +1,27 @@
+* Freescale MXS MMC controller
+
+The Freescale MXS Synchronous Serial Ports (SSP) can act as a MMC controller
+to support MMC, SD, and SDIO types of memory cards.
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the mxsmmc driver.
+
+Required properties:
+- compatible: Should be "fsl,<chip>-mmc".  The supported chips include
+  imx23 and imx28.
+- interrupts: Should contain ERROR interrupt number
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and SSP DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
+
+Examples:
+
+ssp0: ssp@80010000 {
+	compatible = "fsl,imx28-mmc";
+	reg = <0x80010000 2000>;
+	interrupts = <96>;
+	dmas = <&dma_apbh 0>;
+	dma-names = "rx-tx";
+	bus-width = <8>;
+};
diff --git a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt
new file mode 100644
index 00000000..c6d7b11d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt
@@ -0,0 +1,25 @@
+* NVIDIA Tegra Secure Digital Host Controller
+
+This controller on Tegra family SoCs provides an interface for MMC, SD,
+and SDIO types of memory cards.
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the sdhci-tegra driver.
+
+Required properties:
+- compatible : Should be "nvidia,<chip>-sdhci"
+
+Optional properties:
+- power-gpios : Specify GPIOs for power control
+
+Example:
+
+sdhci@c8000200 {
+	compatible = "nvidia,tegra20-sdhci";
+	reg = <0xc8000200 0x200>;
+	interrupts = <47>;
+	cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+	wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+	power-gpios = <&gpio 155 0>; /* gpio PT3 */
+	bus-width = <8>;
+};
diff --git a/Documentation/devicetree/bindings/mmc/orion-sdio.txt b/Documentation/devicetree/bindings/mmc/orion-sdio.txt
new file mode 100644
index 00000000..84f0ebd6
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/orion-sdio.txt
@@ -0,0 +1,17 @@
+* Marvell orion-sdio controller
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the orion-sdio driver.
+
+- compatible: Should be "marvell,orion-sdio"
+- clocks: reference to the clock of the SDIO interface
+
+Example:
+
+	mvsdio@d00d4000 {
+		compatible = "marvell,orion-sdio";
+		reg = <0xd00d4000 0x200>;
+		interrupts = <54>;
+		clocks = <&gateclk 17>;
+		status = "disabled";
+	};
diff --git a/Documentation/devicetree/bindings/mmc/pxa-mmc.txt b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt
new file mode 100644
index 00000000..b7025de7
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt
@@ -0,0 +1,25 @@
+* PXA MMC drivers
+
+Driver bindings for the PXA MCI (MMC/SDIO) interfaces
+
+Required properties:
+- compatible: Should be "marvell,pxa-mmc".
+- vmmc-supply: A regulator for VMMC
+
+Optional properties:
+- marvell,detect-delay-ms: sets the detection delay timeout in ms.
+- marvell,gpio-power: GPIO spec for the card power enable pin
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the pxa-mmc driver.
+
+Examples:
+
+mmc0: mmc@41100000 {
+	compatible = "marvell,pxa-mmc";
+	reg = <0x41100000 0x1000>;
+	interrupts = <23>;
+	cd-gpios = <&gpio 23 0>;
+	wp-gpios = <&gpio 24 0>;
+};
+
diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt
new file mode 100644
index 00000000..328e990d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt
@@ -0,0 +1,32 @@
+* Samsung's SDHCI Controller device tree bindings
+
+Samsung's SDHCI controller is used as a connectivity interface with external
+MMC, SD and eMMC storage mediums. This file documents differences between the
+core mmc properties described by mmc.txt and the properties used by the
+Samsung implmentation of the SDHCI controller.
+
+Required SoC Specific Properties:
+- compatible: should be one of the following
+  - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci
+    controller.
+  - "samsung,exynos4210-sdhci": For controllers compatible with Exynos4 sdhci
+    controller.
+
+Required Board Specific Properties:
+- pinctrl-0: Should specify pin control groups used for this controller.
+- pinctrl-names: Should contain only one value - "default".
+
+Example:
+	sdhci@12530000 {
+		compatible = "samsung,exynos4210-sdhci";
+		reg = <0x12530000 0x100>;
+		interrupts = <0 75 0>;
+		bus-width = <4>;
+		cd-gpios = <&gpk2 2 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
+	};
+
+	Note: This example shows both SoC specific and board specific properties
+	in a single device node. The properties can be actually be separated
+	into SoC specific node and board specific node.
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-dove.txt b/Documentation/devicetree/bindings/mmc/sdhci-dove.txt
new file mode 100644
index 00000000..ae9aab9a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-dove.txt
@@ -0,0 +1,14 @@
+* Marvell sdhci-dove controller
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the sdhci-pxav2 and sdhci-pxav3 drivers.
+
+- compatible: Should be "marvell,dove-sdhci".
+
+Example:
+
+sdio0: sdio@92000 {
+	compatible = "marvell,dove-sdhci";
+	reg = <0x92000 0x100>;
+	interrupts = <35>;
+};
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt
new file mode 100644
index 00000000..dbe98a3c
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt
@@ -0,0 +1,21 @@
+* Marvell sdhci-pxa v2/v3 controller
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the sdhci-pxav2 and sdhci-pxav3 drivers.
+
+Required properties:
+- compatible: Should be "mrvl,pxav2-mmc" or "mrvl,pxav3-mmc".
+
+Optional properties:
+- mrvl,clk-delay-cycles: Specify a number of cycles to delay for tuning.
+
+Example:
+
+sdhci@d4280800 {
+	compatible = "mrvl,pxav3-mmc";
+	reg = <0xd4280800 0x800>;
+	bus-width = <8>;
+	interrupts = <27>;
+	non-removable;
+	mrvl,clk-delay-cycles = <31>;
+};
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-sirf.txt b/Documentation/devicetree/bindings/mmc/sdhci-sirf.txt
new file mode 100644
index 00000000..dd6ed464
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-sirf.txt
@@ -0,0 +1,18 @@
+* SiRFprimII/marco/atlas6 SDHCI Controller
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the sdhci-sirf driver.
+
+Required properties:
+- compatible: sirf,prima2-sdhc
+
+Optional properties:
+- cd-gpios: card detect gpio, with zero flags.
+
+Example:
+
+	sd0: sdhci@56000000 {
+		compatible = "sirf,prima2-sdhc";
+		reg = <0xcd000000 0x100000>;
+		cd-gpios = <&gpio 6 0>;
+	};
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-spear.txt b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt
new file mode 100644
index 00000000..fd3643e7
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt
@@ -0,0 +1,18 @@
+* SPEAr SDHCI Controller
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the sdhci-spear driver.
+
+Required properties:
+- compatible: "st,spear300-sdhci"
+
+Optional properties:
+- cd-gpios: card detect gpio, with zero flags.
+
+Example:
+
+	sdhci@fc000000 {
+		compatible = "st,spear300-sdhci";
+		reg = <0xfc000000 0x1000>;
+		cd-gpios = <&gpio0 6 0>;
+	};
diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
new file mode 100644
index 00000000..726fd212
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
@@ -0,0 +1,87 @@
+* Synopsis Designware Mobile Storage Host Controller
+
+The Synopsis designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core mmc properties described by mmc.txt and the
+properties used by the Synopsis Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be
+	- snps,dw-mshc: for controllers compliant with synopsis dw-mshc.
+* #address-cells: should be 1.
+* #size-cells: should be 0.
+
+# Slots: The slot specific information are contained within child-nodes with
+  each child-node representing a supported slot. There should be atleast one
+  child node representing a card slot. The name of the child node representing
+  the slot is recommended to be slot@n where n is the unique number of the slot
+  connnected to the controller. The following are optional properties which
+  can be included in the slot child node.
+
+	* reg: specifies the physical slot number. The valid values of this
+	  property is 0 to (num-slots -1), where num-slots is the value
+	  specified by the num-slots property.
+
+	* bus-width: as documented in mmc core bindings.
+
+	* wp-gpios: specifies the write protect gpio line. The format of the
+	  gpio specifier depends on the gpio controller. If a GPIO is not used
+	  for write-protect, this property is optional.
+
+	* disable-wp: If the wp-gpios property isn't present then (by default)
+	  we'd assume that the write protect is hooked up directly to the
+	  controller's special purpose write protect line (accessible via
+	  the WRTPRT register).  However, it's possible that we simply don't
+	  want write protect.  In that case specify 'disable-wp'.
+	  NOTE: This property is not required for slots known to always
+	  connect to eMMC or SDIO cards.
+
+Optional properties:
+
+* num-slots: specifies the number of slots supported by the controller.
+  The number of physical slots actually used could be equal or less than the
+  value specified by num-slots. If this property is not specified, the value
+  of num-slot property is assumed to be 1.
+
+* fifo-depth: The maximum size of the tx/rx fifo's. If this property is not
+  specified, the default value of the fifo size is determined from the
+  controller registers.
+
+* card-detect-delay: Delay in milli-seconds before detecting card after card
+  insert event. The default value is 0.
+
+* supports-highspeed: Enables support for high speed cards (upto 50MHz)
+
+* broken-cd: as documented in mmc core bindings.
+
+Aliases:
+
+- All the MSHC controller nodes should be represented in the aliases node using
+  the following format 'mshc{n}' where n is a unique number for the alias.
+
+Example:
+
+The MSHC controller node can be split into two portions, SoC specific and
+board specific portions as listed below.
+
+	dwmmc0@12200000 {
+		compatible = "snps,dw-mshc";
+		reg = <0x12200000 0x1000>;
+		interrupts = <0 75 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	dwmmc0@12200000 {
+		num-slots = <1>;
+		supports-highspeed;
+		broken-cd;
+		fifo-depth = <0x80>;
+		card-detect-delay = <200>;
+
+		slot@0 {
+			reg = <0>;
+			bus-width = <8>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
new file mode 100644
index 00000000..ed271fc2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
@@ -0,0 +1,33 @@
+* TI Highspeed MMC host controller for OMAP
+
+The Highspeed MMC Host Controller on TI OMAP family
+provides an interface for MMC, SD, and SDIO types of memory cards.
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the omap_hsmmc driver.
+
+Required properties:
+- compatible:
+ Should be "ti,omap2-hsmmc", for OMAP2 controllers
+ Should be "ti,omap3-hsmmc", for OMAP3 controllers
+ Should be "ti,omap4-hsmmc", for OMAP4 controllers
+- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1
+
+Optional properties:
+ti,dual-volt: boolean, supports dual voltage cards
+<supply-name>-supply: phandle to the regulator device tree node
+"supply-name" examples are "vmmc", "vmmc_aux" etc
+ti,non-removable: non-removable slot (like eMMC)
+ti,needs-special-reset: Requires a special softreset sequence
+ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed
+
+Example:
+	mmc1: mmc@0x4809c000 {
+		compatible = "ti,omap4-hsmmc";
+		reg = <0x4809c000 0x400>;
+		ti,hwmods = "mmc1";
+		ti,dual-volt;
+		bus-width = <4>;
+		vmmc-supply = <&vmmc>; /* phandle to regulator node */
+		ti,non-removable;
+	};
diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt
new file mode 100644
index 00000000..df204e18
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt
@@ -0,0 +1,20 @@
+* Toshiba Mobile IO SD/MMC controller
+
+The tmio-mmc driver doesn't probe its devices actively, instead its binding to
+devices is managed by either MFD drivers or by the sh_mobile_sdhi platform
+driver. Those drivers supply the tmio-mmc driver with platform data, that either
+describe hardware capabilities, known to them, or are obtained by them from
+their own platform data or from their DT information. In the latter case all
+compulsory and any optional properties, common to all SD/MMC drivers, as
+described in mmc.txt, can be used. Additionally the following tmio_mmc-specific
+optional bindings can be used.
+
+Optional properties:
+- toshiba,mmc-wrprotect-disable: write-protect detection is unavailable
+
+When used with Renesas SDHI hardware, the following compatibility strings
+configure various model-specific properties:
+
+"renesas,sh7372-sdhi":	(default) compatible with SH7372
+"renesas,r8a7740-sdhi":	compatible with R8A7740: certain MMC/SD commands have to
+			wait for the interface to become idle.
diff --git a/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt b/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt
new file mode 100644
index 00000000..d7fb6abb
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt
@@ -0,0 +1,23 @@
+* Wondermedia WM8505/WM8650 SD/MMC Host Controller
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the wmt-sdmmc driver.
+
+Required properties:
+- compatible: Should be "wm,wm8505-sdhc".
+- interrupts: Two interrupts are required - regular irq and dma irq.
+
+Optional properties:
+- sdon-inverted: SD_ON bit is inverted on the controller
+
+Examples:
+
+sdhc@d800a000 {
+	compatible = "wm,wm8505-sdhc";
+	reg = <0xd800a000 0x1000>;
+	interrupts = <20 21>;
+	clocks = <&sdhc>;
+	bus-width = <4>;
+	sdon-inverted;
+};
+