1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
|
//*****************************************************************************
//
// buttons.h - Prototypes for the DK-TM4C129X development board buttons driver.
//
// Copyright (c) 2013-2014 Texas Instruments Incorporated. All rights reserved.
// Software License Agreement
//
// Texas Instruments (TI) is supplying this software for use solely and
// exclusively on TI's microcontroller products. The software is owned by
// TI and/or its suppliers, and is protected under applicable copyright
// laws. You may not combine this software with "viral" open-source
// software in order to form a larger program.
//
// THIS SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS.
// NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT
// NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
// A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. TI SHALL NOT, UNDER ANY
// CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
// DAMAGES, FOR ANY REASON WHATSOEVER.
//
// This is part of revision 2.1.0.12573 of the DK-TM4C129X Firmware Package.
//
//*****************************************************************************
#ifndef __BUTTONS_H__
#define __BUTTONS_H__
//*****************************************************************************
//
// If building with a C++ compiler, make all of the definitions in this header
// have a C binding.
//
//*****************************************************************************
#ifdef __cplusplus
extern "C"
{
#endif
//*****************************************************************************
//
// Defines for the hardware resources used by the pushbuttons.
//
// The switches are on the following ports/pins:
//
// PN3 - Up Button (UP_BUTTON)
// PE5 - Down Button (DOWN_BUTTON)
// PP1 - Select Button (SELECT_BUTTON)
//
// The switches tie the GPIO to ground, so the GPIOs need to be configured
// with pull-ups, and a value of 0 means the switch is pressed.
//
//*****************************************************************************
#define NUM_BUTTONS 3
#define UP_BUTTON GPIO_PIN_3
#define DOWN_BUTTON GPIO_PIN_5
#define SELECT_BUTTON GPIO_PIN_1
#define ALL_BUTTONS (UP_BUTTON | DOWN_BUTTON | SELECT_BUTTON)
//*****************************************************************************
//
// Useful macros for detecting button events.
//
//*****************************************************************************
#define BUTTON_PRESSED(button, buttons, changed) \
(((button) & (changed)) && ((button) & (buttons)))
#define BUTTON_RELEASED(button, buttons, changed) \
(((button) & (changed)) && !((button) & (buttons)))
//*****************************************************************************
//
// If building with a C++ compiler, make all of the definitions in this header
// have a C binding.
//
//*****************************************************************************
#ifdef __cplusplus
extern "C"
{
#endif
//*****************************************************************************
//
// Functions exported from buttons.c
//
//*****************************************************************************
extern void ButtonsInit(uint8_t ui8Buttons);
extern uint8_t ButtonsPoll(uint8_t *pui8Delta, uint8_t *pui8Raw);
//*****************************************************************************
//
// Mark the end of the C bindings section for C++ compilers.
//
//*****************************************************************************
#ifdef __cplusplus
}
#endif
//*****************************************************************************
//
// Prototypes for the globals exported by this driver.
//
//*****************************************************************************
#endif // __BUTTONS_H__
|
