From 8e4bff4cab0ddac6060645b0715210484d02ff40 Mon Sep 17 00:00:00 2001
From: Yuval Adam <_@yuv.al>
Date: Wed, 30 Aug 2017 08:25:59 +0000
Subject: Initial file dump from open source release

---
 arch/arm/mach-omap2/board-omap3evm.c | 735 +++++++++++++++++++++++++++++++++++
 1 file changed, 735 insertions(+)
 create mode 100644 arch/arm/mach-omap2/board-omap3evm.c

(limited to 'arch/arm/mach-omap2/board-omap3evm.c')

diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
new file mode 100644
index 00000000..f76d0de7
--- /dev/null
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -0,0 +1,735 @@
+/*
+ * linux/arch/arm/mach-omap2/board-omap3evm.c
+ *
+ * Copyright (C) 2008 Texas Instruments
+ *
+ * Modified from mach-omap2/board-3430sdp.c
+ *
+ * Initial code: Syed Mohammed Khasim
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/input.h>
+#include <linux/input/matrix_keypad.h>
+#include <linux/leds.h>
+#include <linux/interrupt.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/nand.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <linux/i2c/twl.h>
+#include <linux/usb/otg.h>
+#include <linux/usb/musb.h>
+#include <linux/usb/nop-usb-xceiv.h>
+#include <linux/smsc911x.h>
+
+#include <linux/wl12xx.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
+#include <linux/mmc/host.h>
+#include <linux/export.h>
+#include <linux/usb/phy.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <linux/platform_data/mtd-nand-omap2.h>
+#include "common.h"
+#include <linux/platform_data/spi-omap2-mcspi.h>
+#include <video/omapdss.h>
+#include <video/omap-panel-data.h>
+
+#include "soc.h"
+#include "mux.h"
+#include "sdram-micron-mt46h32m32lf-6.h"
+#include "hsmmc.h"
+#include "common-board-devices.h"
+#include "board-flash.h"
+
+#define	NAND_CS			0
+
+#define OMAP3_EVM_TS_GPIO	175
+#define OMAP3_EVM_EHCI_VBUS	22
+#define OMAP3_EVM_EHCI_SELECT	61
+
+#define OMAP3EVM_ETHR_START	0x2c000000
+#define OMAP3EVM_ETHR_SIZE	1024
+#define OMAP3EVM_ETHR_ID_REV	0x50
+#define OMAP3EVM_ETHR_GPIO_IRQ	176
+#define OMAP3EVM_SMSC911X_CS	5
+/*
+ * Eth Reset signal
+ *	64 = Generation 1 (<=RevD)
+ *	7 = Generation 2 (>=RevE)
+ */
+#define OMAP3EVM_GEN1_ETHR_GPIO_RST	64
+#define OMAP3EVM_GEN2_ETHR_GPIO_RST	7
+
+/*
+ * OMAP35x EVM revision
+ * Run time detection of EVM revision is done by reading Ethernet
+ * PHY ID -
+ *	GEN_1	= 0x01150000
+ *	GEN_2	= 0x92200000
+ */
+enum {
+	OMAP3EVM_BOARD_GEN_1 = 0,	/* EVM Rev between  A - D */
+	OMAP3EVM_BOARD_GEN_2,		/* EVM Rev >= Rev E */
+};
+
+static u8 omap3_evm_version;
+
+static u8 get_omap3_evm_rev(void)
+{
+	return omap3_evm_version;
+}
+
+static void __init omap3_evm_get_revision(void)
+{
+	void __iomem *ioaddr;
+	unsigned int smsc_id;
+
+	/* Ethernet PHY ID is stored at ID_REV register */
+	ioaddr = ioremap_nocache(OMAP3EVM_ETHR_START, SZ_1K);
+	if (!ioaddr)
+		return;
+	smsc_id = readl(ioaddr + OMAP3EVM_ETHR_ID_REV) & 0xFFFF0000;
+	iounmap(ioaddr);
+
+	switch (smsc_id) {
+	/*SMSC9115 chipset*/
+	case 0x01150000:
+		omap3_evm_version = OMAP3EVM_BOARD_GEN_1;
+		break;
+	/*SMSC 9220 chipset*/
+	case 0x92200000:
+	default:
+		omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
+	}
+}
+
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#include "gpmc-smsc911x.h"
+
+static struct omap_smsc911x_platform_data smsc911x_cfg = {
+	.cs             = OMAP3EVM_SMSC911X_CS,
+	.gpio_irq       = OMAP3EVM_ETHR_GPIO_IRQ,
+	.gpio_reset     = -EINVAL,
+	.flags		= SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
+};
+
+static inline void __init omap3evm_init_smsc911x(void)
+{
+	/* Configure ethernet controller reset gpio */
+	if (cpu_is_omap3430()) {
+		if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1)
+			smsc911x_cfg.gpio_reset = OMAP3EVM_GEN1_ETHR_GPIO_RST;
+		else
+			smsc911x_cfg.gpio_reset = OMAP3EVM_GEN2_ETHR_GPIO_RST;
+	}
+
+	gpmc_smsc911x_init(&smsc911x_cfg);
+}
+
+#else
+static inline void __init omap3evm_init_smsc911x(void) { return; }
+#endif
+
+/*
+ * OMAP3EVM LCD Panel control signals
+ */
+#define OMAP3EVM_LCD_PANEL_LR		2
+#define OMAP3EVM_LCD_PANEL_UD		3
+#define OMAP3EVM_LCD_PANEL_INI		152
+#define OMAP3EVM_LCD_PANEL_QVGA		154
+#define OMAP3EVM_LCD_PANEL_RESB		155
+
+#define OMAP3EVM_LCD_PANEL_ENVDD	153
+#define OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO	210
+
+/*
+ * OMAP3EVM DVI control signals
+ */
+#define OMAP3EVM_DVI_PANEL_EN_GPIO	199
+
+static struct panel_sharp_ls037v7dw01_data omap3_evm_lcd_data = {
+	.resb_gpio = OMAP3EVM_LCD_PANEL_RESB,
+	.ini_gpio = OMAP3EVM_LCD_PANEL_INI,
+	.mo_gpio = OMAP3EVM_LCD_PANEL_QVGA,
+	.lr_gpio = OMAP3EVM_LCD_PANEL_LR,
+	.ud_gpio = OMAP3EVM_LCD_PANEL_UD,
+};
+
+static void __init omap3_evm_display_init(void)
+{
+	int r;
+
+	r = gpio_request_one(OMAP3EVM_LCD_PANEL_ENVDD, GPIOF_OUT_INIT_LOW,
+				"lcd_panel_envdd");
+	if (r)
+		pr_err("failed to get lcd_panel_envdd GPIO\n");
+
+	r = gpio_request_one(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO,
+				GPIOF_OUT_INIT_LOW, "lcd_panel_bklight");
+	if (r)
+		pr_err("failed to get lcd_panel_bklight GPIO\n");
+
+	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
+		gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 0);
+	else
+		gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 1);
+}
+
+static struct omap_dss_device omap3_evm_lcd_device = {
+	.name			= "lcd",
+	.driver_name		= "sharp_ls_panel",
+	.type			= OMAP_DISPLAY_TYPE_DPI,
+	.phy.dpi.data_lines	= 18,
+	.data			= &omap3_evm_lcd_data,
+};
+
+static struct omap_dss_device omap3_evm_tv_device = {
+	.name			= "tv",
+	.driver_name		= "venc",
+	.type			= OMAP_DISPLAY_TYPE_VENC,
+	.phy.venc.type		= OMAP_DSS_VENC_TYPE_SVIDEO,
+};
+
+static struct tfp410_platform_data dvi_panel = {
+	.power_down_gpio	= OMAP3EVM_DVI_PANEL_EN_GPIO,
+	.i2c_bus_num		= -1,
+};
+
+static struct omap_dss_device omap3_evm_dvi_device = {
+	.name			= "dvi",
+	.type			= OMAP_DISPLAY_TYPE_DPI,
+	.driver_name		= "tfp410",
+	.data			= &dvi_panel,
+	.phy.dpi.data_lines	= 24,
+};
+
+static struct omap_dss_device *omap3_evm_dss_devices[] = {
+	&omap3_evm_lcd_device,
+	&omap3_evm_tv_device,
+	&omap3_evm_dvi_device,
+};
+
+static struct omap_dss_board_info omap3_evm_dss_data = {
+	.num_devices	= ARRAY_SIZE(omap3_evm_dss_devices),
+	.devices	= omap3_evm_dss_devices,
+	.default_device	= &omap3_evm_lcd_device,
+};
+
+static struct regulator_consumer_supply omap3evm_vmmc1_supply[] = {
+	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
+};
+
+static struct regulator_consumer_supply omap3evm_vsim_supply[] = {
+	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
+};
+
+/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
+static struct regulator_init_data omap3evm_vmmc1 = {
+	.constraints = {
+		.min_uV			= 1850000,
+		.max_uV			= 3150000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= ARRAY_SIZE(omap3evm_vmmc1_supply),
+	.consumer_supplies	= omap3evm_vmmc1_supply,
+};
+
+/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
+static struct regulator_init_data omap3evm_vsim = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 3000000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= ARRAY_SIZE(omap3evm_vsim_supply),
+	.consumer_supplies	= omap3evm_vsim_supply,
+};
+
+static struct omap2_hsmmc_info mmc[] = {
+	{
+		.mmc		= 1,
+		.caps		= MMC_CAP_4_BIT_DATA,
+		.gpio_cd	= -EINVAL,
+		.gpio_wp	= 63,
+		.deferred	= true,
+	},
+#ifdef CONFIG_WILINK_PLATFORM_DATA
+	{
+		.name		= "wl1271",
+		.mmc		= 2,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD,
+		.gpio_wp	= -EINVAL,
+		.gpio_cd	= -EINVAL,
+		.nonremovable	= true,
+	},
+#endif
+	{}	/* Terminator */
+};
+
+static struct gpio_led gpio_leds[] = {
+	{
+		.name			= "omap3evm::ledb",
+		/* normally not visible (board underside) */
+		.default_trigger	= "default-on",
+		.gpio			= -EINVAL,	/* gets replaced */
+		.active_low		= true,
+	},
+};
+
+static struct gpio_led_platform_data gpio_led_info = {
+	.leds		= gpio_leds,
+	.num_leds	= ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device leds_gpio = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &gpio_led_info,
+	},
+};
+
+
+static int omap3evm_twl_gpio_setup(struct device *dev,
+		unsigned gpio, unsigned ngpio)
+{
+	int r, lcd_bl_en;
+
+	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
+	mmc[0].gpio_cd = gpio + 0;
+	omap_hsmmc_late_init(mmc);
+
+	/*
+	 * Most GPIOs are for USB OTG.  Some are mostly sent to
+	 * the P2 connector; notably LEDA for the LCD backlight.
+	 */
+
+	/* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
+	lcd_bl_en = get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2 ?
+		GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
+	r = gpio_request_one(gpio + TWL4030_GPIO_MAX, lcd_bl_en, "EN_LCD_BKL");
+	if (r)
+		printk(KERN_ERR "failed to get/set lcd_bkl gpio\n");
+
+	/* gpio + 7 == DVI Enable */
+	gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
+
+	/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
+	gpio_leds[0].gpio = gpio + TWL4030_GPIO_MAX + 1;
+
+	platform_device_register(&leds_gpio);
+
+	/* Enable VBUS switch by setting TWL4030.GPIO2DIR as output
+	 * for starting USB tranceiver
+	 */
+#ifdef CONFIG_TWL4030_CORE
+	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
+		u8 val;
+
+		twl_i2c_read_u8(TWL4030_MODULE_GPIO, &val, REG_GPIODATADIR1);
+		val |= 0x04; /* TWL4030.GPIO2DIR BIT at GPIODATADIR1(0x9B) */
+		twl_i2c_write_u8(TWL4030_MODULE_GPIO, val, REG_GPIODATADIR1);
+	}
+#endif
+
+	return 0;
+}
+
+static struct twl4030_gpio_platform_data omap3evm_gpio_data = {
+	.use_leds	= true,
+	.setup		= omap3evm_twl_gpio_setup,
+};
+
+static uint32_t board_keymap[] = {
+	KEY(0, 0, KEY_LEFT),
+	KEY(0, 1, KEY_DOWN),
+	KEY(0, 2, KEY_ENTER),
+	KEY(0, 3, KEY_M),
+
+	KEY(1, 0, KEY_RIGHT),
+	KEY(1, 1, KEY_UP),
+	KEY(1, 2, KEY_I),
+	KEY(1, 3, KEY_N),
+
+	KEY(2, 0, KEY_A),
+	KEY(2, 1, KEY_E),
+	KEY(2, 2, KEY_J),
+	KEY(2, 3, KEY_O),
+
+	KEY(3, 0, KEY_B),
+	KEY(3, 1, KEY_F),
+	KEY(3, 2, KEY_K),
+	KEY(3, 3, KEY_P)
+};
+
+static struct matrix_keymap_data board_map_data = {
+	.keymap			= board_keymap,
+	.keymap_size		= ARRAY_SIZE(board_keymap),
+};
+
+static struct twl4030_keypad_data omap3evm_kp_data = {
+	.keymap_data	= &board_map_data,
+	.rows		= 4,
+	.cols		= 4,
+	.rep		= 1,
+};
+
+/* ads7846 on SPI */
+static struct regulator_consumer_supply omap3evm_vio_supply[] = {
+	REGULATOR_SUPPLY("vcc", "spi1.0"),
+};
+
+/* VIO for ads7846 */
+static struct regulator_init_data omap3evm_vio = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 1800000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= ARRAY_SIZE(omap3evm_vio_supply),
+	.consumer_supplies	= omap3evm_vio_supply,
+};
+
+#ifdef CONFIG_WILINK_PLATFORM_DATA
+
+#define OMAP3EVM_WLAN_PMENA_GPIO	(150)
+#define OMAP3EVM_WLAN_IRQ_GPIO		(149)
+
+static struct regulator_consumer_supply omap3evm_vmmc2_supply[] = {
+	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
+};
+
+/* VMMC2 for driving the WL12xx module */
+static struct regulator_init_data omap3evm_vmmc2 = {
+	.constraints = {
+		.valid_ops_mask	= REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= ARRAY_SIZE(omap3evm_vmmc2_supply),
+	.consumer_supplies	= omap3evm_vmmc2_supply,
+};
+
+static struct fixed_voltage_config omap3evm_vwlan = {
+	.supply_name		= "vwl1271",
+	.microvolts		= 1800000, /* 1.80V */
+	.gpio			= OMAP3EVM_WLAN_PMENA_GPIO,
+	.startup_delay		= 70000, /* 70ms */
+	.enable_high		= 1,
+	.enabled_at_boot	= 0,
+	.init_data		= &omap3evm_vmmc2,
+};
+
+static struct platform_device omap3evm_wlan_regulator = {
+	.name		= "reg-fixed-voltage",
+	.id		= 1,
+	.dev = {
+		.platform_data	= &omap3evm_vwlan,
+	},
+};
+
+struct wl12xx_platform_data omap3evm_wlan_data __initdata = {
+	.board_ref_clock = WL12XX_REFCLOCK_38, /* 38.4 MHz */
+};
+#endif
+
+/* VAUX2 for USB */
+static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
+	REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"),	/* OMAP ISP */
+	REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"),	/* OMAP ISP */
+	REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"),	/* hsusb port 2 */
+	REGULATOR_SUPPLY("vaux2", NULL),
+};
+
+static struct regulator_init_data omap3evm_vaux2 = {
+	.constraints = {
+		.min_uV		= 2800000,
+		.max_uV		= 2800000,
+		.apply_uV	= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies		= ARRAY_SIZE(omap3evm_vaux2_supplies),
+	.consumer_supplies		= omap3evm_vaux2_supplies,
+};
+
+static struct twl4030_platform_data omap3evm_twldata = {
+	/* platform_data for children goes here */
+	.keypad		= &omap3evm_kp_data,
+	.gpio		= &omap3evm_gpio_data,
+	.vio		= &omap3evm_vio,
+	.vmmc1		= &omap3evm_vmmc1,
+	.vsim		= &omap3evm_vsim,
+};
+
+static int __init omap3_evm_i2c_init(void)
+{
+	omap3_pmic_get_config(&omap3evm_twldata,
+			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
+			TWL_COMMON_PDATA_AUDIO,
+			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
+
+	omap3evm_twldata.vdac->constraints.apply_uV = true;
+	omap3evm_twldata.vpll2->constraints.apply_uV = true;
+
+	omap3_pmic_init("twl4030", &omap3evm_twldata);
+	omap_register_i2c_bus(2, 400, NULL, 0);
+	omap_register_i2c_bus(3, 400, NULL, 0);
+	return 0;
+}
+
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 2,
+		.reset_gpio = -1,	/* set at runtime */
+		.vcc_gpio = -EINVAL,
+	},
+};
+
+static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
+	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+};
+
+#ifdef CONFIG_OMAP_MUX
+static struct omap_board_mux omap35x_board_mux[] __initdata = {
+	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
+				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
+				OMAP_PIN_OFF_WAKEUPENABLE),
+	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
+				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
+				OMAP_PIN_OFF_WAKEUPENABLE),
+	OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
+				OMAP_PIN_OFF_NONE),
+	OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
+				OMAP_PIN_OFF_NONE),
+#ifdef CONFIG_WILINK_PLATFORM_DATA
+	/* WLAN IRQ - GPIO 149 */
+	OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
+
+	/* WLAN POWER ENABLE - GPIO 150 */
+	OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
+
+	/* MMC2 SDIO pin muxes for WL12xx */
+	OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+#endif
+	{ .reg_offset = OMAP_MUX_TERMINATOR },
+};
+
+static struct omap_board_mux omap36x_board_mux[] __initdata = {
+	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
+				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
+				OMAP_PIN_OFF_WAKEUPENABLE),
+	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
+				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
+				OMAP_PIN_OFF_WAKEUPENABLE),
+	/* AM/DM37x EVM: DSS data bus muxed with sys_boot */
+	OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
+	OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
+	OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
+	OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
+	OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
+	OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
+	OMAP3_MUX(SYS_BOOT0, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
+	OMAP3_MUX(SYS_BOOT1, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
+	OMAP3_MUX(SYS_BOOT3, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
+	OMAP3_MUX(SYS_BOOT4, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
+	OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
+	OMAP3_MUX(SYS_BOOT6, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
+#ifdef CONFIG_WILINK_PLATFORM_DATA
+	/* WLAN IRQ - GPIO 149 */
+	OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
+
+	/* WLAN POWER ENABLE - GPIO 150 */
+	OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
+
+	/* MMC2 SDIO pin muxes for WL12xx */
+	OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+#endif
+
+	{ .reg_offset = OMAP_MUX_TERMINATOR },
+};
+#else
+#define omap35x_board_mux	NULL
+#define omap36x_board_mux	NULL
+#endif
+
+static struct omap_musb_board_data musb_board_data = {
+	.interface_type		= MUSB_INTERFACE_ULPI,
+	.mode			= MUSB_OTG,
+	.power			= 100,
+};
+
+static struct gpio omap3_evm_ehci_gpios[] __initdata = {
+	{ OMAP3_EVM_EHCI_VBUS,	 GPIOF_OUT_INIT_HIGH,  "enable EHCI VBUS" },
+	{ OMAP3_EVM_EHCI_SELECT, GPIOF_OUT_INIT_LOW,   "select EHCI port" },
+};
+
+static void __init omap3_evm_wl12xx_init(void)
+{
+#ifdef CONFIG_WILINK_PLATFORM_DATA
+	int ret;
+
+	/* WL12xx WLAN Init */
+	omap3evm_wlan_data.irq = gpio_to_irq(OMAP3EVM_WLAN_IRQ_GPIO);
+	ret = wl12xx_set_platform_data(&omap3evm_wlan_data);
+	if (ret)
+		pr_err("error setting wl12xx data: %d\n", ret);
+	ret = platform_device_register(&omap3evm_wlan_regulator);
+	if (ret)
+		pr_err("error registering wl12xx device: %d\n", ret);
+#endif
+}
+
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
+};
+
+static struct mtd_partition omap3evm_nand_partitions[] = {
+	/* All the partition sizes are listed in terms of NAND block size */
+	{
+		.name           = "X-Loader",
+		.offset         = 0,
+		.size           = 4*(SZ_128K),
+		.mask_flags     = MTD_WRITEABLE
+	},
+	{
+		.name           = "U-Boot",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = 14*(SZ_128K),
+		.mask_flags     = MTD_WRITEABLE
+	},
+	{
+		.name           = "U-Boot Env",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = 2*(SZ_128K)
+	},
+	{
+		.name           = "Kernel",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = 40*(SZ_128K)
+	},
+	{
+		.name           = "File system",
+		.size           = MTDPART_SIZ_FULL,
+		.offset         = MTDPART_OFS_APPEND,
+	},
+};
+
+static void __init omap3_evm_init(void)
+{
+	struct omap_board_mux *obm;
+
+	omap3_evm_get_revision();
+	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
+	obm = (cpu_is_omap3630()) ? omap36x_board_mux : omap35x_board_mux;
+	omap3_mux_init(obm, OMAP_PACKAGE_CBB);
+
+	omap_mux_init_gpio(63, OMAP_PIN_INPUT);
+	omap_hsmmc_init(mmc);
+
+	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
+		omap3evm_twldata.vaux2 = &omap3evm_vaux2;
+
+	omap3_evm_i2c_init();
+
+	omap_display_init(&omap3_evm_dss_data);
+
+	omap_serial_init();
+	omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
+
+	/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
+	usb_nop_xceiv_register();
+
+	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
+		/* enable EHCI VBUS using GPIO22 */
+		omap_mux_init_gpio(OMAP3_EVM_EHCI_VBUS, OMAP_PIN_INPUT_PULLUP);
+		/* Select EHCI port on main board */
+		omap_mux_init_gpio(OMAP3_EVM_EHCI_SELECT,
+				   OMAP_PIN_INPUT_PULLUP);
+		gpio_request_array(omap3_evm_ehci_gpios,
+				   ARRAY_SIZE(omap3_evm_ehci_gpios));
+
+		/* setup EHCI phy reset config */
+		omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
+		phy_data[0].reset_gpio = 21;
+
+		/* EVM REV >= E can supply 500mA with EXTVBUS programming */
+		musb_board_data.power = 500;
+		musb_board_data.extvbus = 1;
+	} else {
+		/* setup EHCI phy reset on MDC */
+		omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
+		phy_data[0].reset_gpio = 135;
+	}
+	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
+	usb_musb_init(&musb_board_data);
+
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
+	usbhs_init(&usbhs_bdata);
+	board_nand_init(omap3evm_nand_partitions,
+			ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS,
+			NAND_BUSWIDTH_16, NULL);
+
+	omap_ads7846_init(1, OMAP3_EVM_TS_GPIO, 310, NULL);
+	omap3evm_init_smsc911x();
+	omap3_evm_display_init();
+	omap3_evm_wl12xx_init();
+	omap_twl4030_audio_init("omap3evm", NULL);
+}
+
+MACHINE_START(OMAP3EVM, "OMAP3 EVM")
+	/* Maintainer: Syed Mohammed Khasim - Texas Instruments */
+	.atag_offset	= 0x100,
+	.reserve	= omap_reserve,
+	.map_io		= omap3_map_io,
+	.init_early	= omap35xx_init_early,
+	.init_irq	= omap3_init_irq,
+	.handle_irq	= omap3_intc_handle_irq,
+	.init_machine	= omap3_evm_init,
+	.init_late	= omap35xx_init_late,
+	.init_time	= omap3_sync32k_timer_init,
+	.restart	= omap3xxx_restart,
+MACHINE_END
-- 
cgit v1.3.1