//*****************************************************************************
//
// bl_config.c - A dummy C file to generate bl_config.in from bl_config.h.
//
// Copyright (c) 2007-2014 Texas Instruments Incorporated.  All rights reserved.
// Software License Agreement
// 
// Texas Instruments (TI) is supplying this software for use solely and
// exclusively on TI's microcontroller products. The software is owned by
// TI and/or its suppliers, and is protected under applicable copyright
// laws. You may not combine this software with "viral" open-source
// software in order to form a larger program.
// 
// THIS SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS.
// NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT
// NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
// A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. TI SHALL NOT, UNDER ANY
// CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
// DAMAGES, FOR ANY REASON WHATSOEVER.
// 
// This is part of revision 2.1.0.12573 of the Tiva Firmware Development Package.
//
//*****************************************************************************

#include "bl_config.h"

//*****************************************************************************
//
// Since the RV-MDK assembler is not able to run assembly code through the C
// preprocessor, the relevant contents of bl_config.h need to be converted to
// assembly format for inclusion into the RV-MDK startup code.  This file
// performs this conversion when manually run through the C preprocessor via:
//
//     armcc --device DLM -o bl_config.inc -E bl_config.c
//
// This file does not contain valid C code and will fail to compile (-E tells
// the compiler to preprocess but not attempt to compile the code).
//
//*****************************************************************************

//*****************************************************************************
//
// Define an assembler symbol for the stack size.
//
//*****************************************************************************
_STACK_SIZE                     equ     STACK_SIZE

//*****************************************************************************
//
// Define an assembler symbol for the application starting address.
//
//*****************************************************************************
_APP_START_ADDRESS              equ     APP_START_ADDRESS

//*****************************************************************************
//
// Define an assembler symbol for the application vector table address.
//
//*****************************************************************************
_VTABLE_START_ADDRESS           equ     VTABLE_START_ADDRESS

//*****************************************************************************
//
// Define an assembler symbol if the MOSCFAIL handler is enabled.
//
//*****************************************************************************
#ifdef ENABLE_MOSCFAIL_HANDLER
_ENABLE_MOSCFAIL_HANDLER        equ     1
#endif

//*****************************************************************************
//
// Define an assembler symbol if update via the UART is enabled.
//
//*****************************************************************************
#ifdef UART_ENABLE_UPDATE
_UART_ENABLE_UPDATE             equ     1
#endif

//*****************************************************************************
//
// Define an assember symbol if UART autobauding is enabled.
//
//*****************************************************************************
#ifdef UART_AUTOBAUD
_UART_AUTOBAUD                  equ     1
#endif

//*****************************************************************************
//
// Define an assembler symbol if update via Ethernet is enabled.
//
//*****************************************************************************
#ifdef ENET_ENABLE_UPDATE
_ENET_ENABLE_UPDATE             equ     1
#endif

//*****************************************************************************
//
// Define an assembler symbol if update via CAN is enabled.
//
//*****************************************************************************
#ifdef CAN_ENABLE_UPDATE
_CAN_ENABLE_UPDATE              equ     1
#endif

//*****************************************************************************
//
// Define an assembler symbol if update via USB is enabled.
//
//*****************************************************************************
#ifdef USB_ENABLE_UPDATE
_USB_ENABLE_UPDATE              equ     1
#endif

//*****************************************************************************
//
// Define an assembler symbol if a hardware initialization hook is provided.
//
//*****************************************************************************
#ifdef BL_HW_INIT_FN_HOOK
#define _quote(x)               #x
#define quote(x)                _quote(x)
                                gbls    _BL_HW_INIT_FN_HOOK
_BL_HW_INIT_FN_HOOK             sets    quote(BL_HW_INIT_FN_HOOK)
#undef _quote
#undef quote
#endif

//*****************************************************************************
//
// Define an assembler symbol if an initialization hook is provided.
//
//*****************************************************************************
#ifdef BL_INIT_FN_HOOK
#define _quote(x)               #x
#define quote(x)                _quote(x)
                                gbls    _BL_INIT_FN_HOOK
_BL_INIT_FN_HOOK                sets    quote(BL_INIT_FN_HOOK)
#undef _quote
#undef quote
#endif

//*****************************************************************************
//
// Define an assembler symbol if a re-initialization hook is provided.
//
//*****************************************************************************
#ifdef BL_REINIT_FN_HOOK
#define _quote(x)               #x
#define quote(x)                _quote(x)
                                gbls    _BL_REINIT_FN_HOOK
_BL_REINIT_FN_HOOK              sets    quote(BL_REINIT_FN_HOOK)
#undef _quote
#undef quote
#endif

//*****************************************************************************
//
// The assembler will require an end statement at the end of the output
// bl_config.inc file.
//
//*****************************************************************************
    end