From c3e4c9a25c2910d2d66d52215b3406b13d5b23d5 Mon Sep 17 00:00:00 2001 From: Yuval Adam Date: Sun, 29 Jun 2014 12:34:32 +0300 Subject: Add more board models --- boards/ek-lm4f232/sd_card/sd_card.c | 915 ++++++++++++++++++++++++++++++++++++ 1 file changed, 915 insertions(+) create mode 100644 boards/ek-lm4f232/sd_card/sd_card.c (limited to 'boards/ek-lm4f232/sd_card/sd_card.c') diff --git a/boards/ek-lm4f232/sd_card/sd_card.c b/boards/ek-lm4f232/sd_card/sd_card.c new file mode 100644 index 0000000..7c67934 --- /dev/null +++ b/boards/ek-lm4f232/sd_card/sd_card.c @@ -0,0 +1,915 @@ +//***************************************************************************** +// +// sd_card.c - Example program for reading files from an SD card. +// +// Copyright (c) 2011-2014 Texas Instruments Incorporated. All rights reserved. +// Software License Agreement +// +// Texas Instruments (TI) is supplying this software for use solely and +// exclusively on TI's microcontroller products. The software is owned by +// TI and/or its suppliers, and is protected under applicable copyright +// laws. You may not combine this software with "viral" open-source +// software in order to form a larger program. +// +// THIS SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS. +// NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT +// NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR +// A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. TI SHALL NOT, UNDER ANY +// CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL +// DAMAGES, FOR ANY REASON WHATSOEVER. +// +// This is part of revision 2.1.0.12573 of the EK-LM4F232 Firmware Package. +// +//***************************************************************************** + +#include +#include +#include +#include "inc/hw_memmap.h" +#include "driverlib/fpu.h" +#include "driverlib/gpio.h" +#include "driverlib/interrupt.h" +#include "driverlib/pin_map.h" +#include "driverlib/rom.h" +#include "driverlib/sysctl.h" +#include "driverlib/systick.h" +#include "driverlib/uart.h" +#include "grlib/grlib.h" +#include "utils/cmdline.h" +#include "utils/uartstdio.h" +#include "fatfs/src/ff.h" +#include "fatfs/src/diskio.h" +#include "drivers/cfal96x64x16.h" + +//***************************************************************************** +// +//! \addtogroup example_list +//!

SD card using FAT file system (sd_card)

+//! +//! This example application demonstrates reading a file system from an SD +//! card. It makes use of FatFs, a FAT file system driver. It provides a +//! simple command console via a serial port for issuing commands to view and +//! navigate the file system on the SD card. +//! +//! The first UART, which is connected to the USB debug virtual serial port on +//! the evaluation board, is configured for 115,200 bits per second, and 8-N-1 +//! mode. When the program is started a message will be printed to the +//! terminal. Type ``help'' for command help. +//! +//! For additional details about FatFs, see the following site: +//! http://elm-chan.org/fsw/ff/00index_e.html +// +//***************************************************************************** + +//***************************************************************************** +// +// Defines the size of the buffers that hold the path, or temporary data from +// the SD card. There are two buffers allocated of this size. The buffer size +// must be large enough to hold the longest expected full path name, including +// the file name, and a trailing null character. +// +//***************************************************************************** +#define PATH_BUF_SIZE 80 + +//***************************************************************************** +// +// Defines the size of the buffer that holds the command line. +// +//***************************************************************************** +#define CMD_BUF_SIZE 64 + +//***************************************************************************** +// +// This buffer holds the full path to the current working directory. Initially +// it is root ("/"). +// +//***************************************************************************** +static char g_pcCwdBuf[PATH_BUF_SIZE] = "/"; + +//***************************************************************************** +// +// A temporary data buffer used when manipulating file paths, or reading data +// from the SD card. +// +//***************************************************************************** +static char g_pcTmpBuf[PATH_BUF_SIZE]; + +//***************************************************************************** +// +// The buffer that holds the command line. +// +//***************************************************************************** +static char g_pcCmdBuf[CMD_BUF_SIZE]; + +//***************************************************************************** +// +// The following are data structures used by FatFs. +// +//***************************************************************************** +static FATFS g_sFatFs; +static DIR g_sDirObject; +static FILINFO g_sFileInfo; +static FIL g_sFileObject; + +//***************************************************************************** +// +// A structure that holds a mapping between an FRESULT numerical code, and a +// string representation. FRESULT codes are returned from the FatFs FAT file +// system driver. +// +//***************************************************************************** +typedef struct +{ + FRESULT iFResult; + char *pcResultStr; +} +tFResultString; + +//***************************************************************************** +// +// A macro to make it easy to add result codes to the table. +// +//***************************************************************************** +#define FRESULT_ENTRY(f) { (f), (#f) } + +//***************************************************************************** +// +// A table that holds a mapping between the numerical FRESULT code and it's +// name as a string. This is used for looking up error codes for printing to +// the console. +// +//***************************************************************************** +tFResultString g_psFResultStrings[] = +{ + FRESULT_ENTRY(FR_OK), + FRESULT_ENTRY(FR_DISK_ERR), + FRESULT_ENTRY(FR_INT_ERR), + FRESULT_ENTRY(FR_NOT_READY), + FRESULT_ENTRY(FR_NO_FILE), + FRESULT_ENTRY(FR_NO_PATH), + FRESULT_ENTRY(FR_INVALID_NAME), + FRESULT_ENTRY(FR_DENIED), + FRESULT_ENTRY(FR_EXIST), + FRESULT_ENTRY(FR_INVALID_OBJECT), + FRESULT_ENTRY(FR_WRITE_PROTECTED), + FRESULT_ENTRY(FR_INVALID_DRIVE), + FRESULT_ENTRY(FR_NOT_ENABLED), + FRESULT_ENTRY(FR_NO_FILESYSTEM), + FRESULT_ENTRY(FR_MKFS_ABORTED), + FRESULT_ENTRY(FR_TIMEOUT), + FRESULT_ENTRY(FR_LOCKED), + FRESULT_ENTRY(FR_NOT_ENOUGH_CORE), + FRESULT_ENTRY(FR_TOO_MANY_OPEN_FILES), + FRESULT_ENTRY(FR_INVALID_PARAMETER), +}; + +//***************************************************************************** +// +// A macro that holds the number of result codes. +// +//***************************************************************************** +#define NUM_FRESULT_CODES (sizeof(g_psFResultStrings) / \ + sizeof(tFResultString)) + +//***************************************************************************** +// +// Graphics context used to show text on the CSTN display. +// +//***************************************************************************** +tContext g_sContext; + +//***************************************************************************** +// +// This function returns a string representation of an error code that was +// returned from a function call to FatFs. It can be used for printing human +// readable error messages. +// +//***************************************************************************** +const char * +StringFromFResult(FRESULT iFResult) +{ + uint_fast8_t ui8Idx; + + // + // Enter a loop to search the error code table for a matching error code. + // + for(ui8Idx = 0; ui8Idx < NUM_FRESULT_CODES; ui8Idx++) + { + // + // If a match is found, then return the string name of the error code. + // + if(g_psFResultStrings[ui8Idx].iFResult == iFResult) + { + return(g_psFResultStrings[ui8Idx].pcResultStr); + } + } + + // + // At this point no matching code was found, so return a string indicating + // an unknown error. + // + return("UNKNOWN ERROR CODE"); +} + +//***************************************************************************** +// +// This is the handler for this SysTick interrupt. FatFs requires a timer tick +// every 10 ms for internal timing purposes. +// +//***************************************************************************** +void +SysTickHandler(void) +{ + // + // Call the FatFs tick timer. + // + disk_timerproc(); +} + +//***************************************************************************** +// +// This function implements the "ls" command. It opens the current directory +// and enumerates through the contents, and prints a line for each item it +// finds. It shows details such as file attributes, time and date, and the +// file size, along with the name. It shows a summary of file sizes at the end +// along with free space. +// +//***************************************************************************** +int +Cmd_ls(int argc, char *argv[]) +{ + uint32_t ui32TotalSize; + uint32_t ui32FileCount; + uint32_t ui32DirCount; + FRESULT iFResult; + FATFS *psFatFs; + char *pcFileName; +#if _USE_LFN + char pucLfn[_MAX_LFN + 1]; + g_sFileInfo.lfname = pucLfn; + g_sFileInfo.lfsize = sizeof(pucLfn); +#endif + + + // + // Open the current directory for access. + // + iFResult = f_opendir(&g_sDirObject, g_pcCwdBuf); + + // + // Check for error and return if there is a problem. + // + if(iFResult != FR_OK) + { + return((int)iFResult); + } + + ui32TotalSize = 0; + ui32FileCount = 0; + ui32DirCount = 0; + + // + // Give an extra blank line before the listing. + // + UARTprintf("\n"); + + // + // Enter loop to enumerate through all directory entries. + // + for(;;) + { + // + // Read an entry from the directory. + // + iFResult = f_readdir(&g_sDirObject, &g_sFileInfo); + + // + // Check for error and return if there is a problem. + // + if(iFResult != FR_OK) + { + return((int)iFResult); + } + + // + // If the file name is blank, then this is the end of the listing. + // + if(!g_sFileInfo.fname[0]) + { + break; + } + + // + // If the attribue is directory, then increment the directory count. + // + if(g_sFileInfo.fattrib & AM_DIR) + { + ui32DirCount++; + } + + // + // Otherwise, it is a file. Increment the file count, and add in the + // file size to the total. + // + else + { + ui32FileCount++; + ui32TotalSize += g_sFileInfo.fsize; + } + +#if _USE_LFN + pcFileName = ((*g_sFileInfo.lfname)?g_sFileInfo.lfname:g_sFileInfo.fname); +#else + pcFileName = g_sFileInfo.fname; +#endif + // + // Print the entry information on a single line with formatting to show + // the attributes, date, time, size, and name. + // + UARTprintf("%c%c%c%c%c %u/%02u/%02u %02u:%02u %9u %s\n", + (g_sFileInfo.fattrib & AM_DIR) ? 'D' : '-', + (g_sFileInfo.fattrib & AM_RDO) ? 'R' : '-', + (g_sFileInfo.fattrib & AM_HID) ? 'H' : '-', + (g_sFileInfo.fattrib & AM_SYS) ? 'S' : '-', + (g_sFileInfo.fattrib & AM_ARC) ? 'A' : '-', + (g_sFileInfo.fdate >> 9) + 1980, + (g_sFileInfo.fdate >> 5) & 15, + g_sFileInfo.fdate & 31, + (g_sFileInfo.ftime >> 11), + (g_sFileInfo.ftime >> 5) & 63, + g_sFileInfo.fsize, + pcFileName); + } + + // + // Print summary lines showing the file, dir, and size totals. + // + UARTprintf("\n%4u File(s),%10u bytes total\n%4u Dir(s)", + ui32FileCount, ui32TotalSize, ui32DirCount); + + // + // Get the free space. + // + iFResult = f_getfree("/", (DWORD *)&ui32TotalSize, &psFatFs); + + // + // Check for error and return if there is a problem. + // + if(iFResult != FR_OK) + { + return((int)iFResult); + } + + // + // Display the amount of free space that was calculated. + // + UARTprintf(", %10uK bytes free\n", (ui32TotalSize * + psFatFs->free_clust / 2)); + + // + // Made it to here, return with no errors. + // + return(0); +} + +//***************************************************************************** +// +// This function implements the "cd" command. It takes an argument that +// specifies the directory to make the current working directory. Path +// separators must use a forward slash "/". The argument to cd can be one of +// the following: +// +// * root ("/") +// * a fully specified path ("/my/path/to/mydir") +// * a single directory name that is in the current directory ("mydir") +// * parent directory ("..") +// +// It does not understand relative paths, so dont try something like this: +// ("../my/new/path") +// +// Once the new directory is specified, it attempts to open the directory to +// make sure it exists. If the new path is opened successfully, then the +// current working directory (cwd) is changed to the new path. +// +//***************************************************************************** +int +Cmd_cd(int argc, char *argv[]) +{ + uint_fast8_t ui8Idx; + FRESULT iFResult; + + // + // Copy the current working path into a temporary buffer so it can be + // manipulated. + // + strcpy(g_pcTmpBuf, g_pcCwdBuf); + + // + // If the first character is /, then this is a fully specified path, and it + // should just be used as-is. + // + if(argv[1][0] == '/') + { + // + // Make sure the new path is not bigger than the cwd buffer. + // + if(strlen(argv[1]) + 1 > sizeof(g_pcCwdBuf)) + { + UARTprintf("Resulting path name is too long\n"); + return(0); + } + + // + // If the new path name (in argv[1]) is not too long, then copy it + // into the temporary buffer so it can be checked. + // + else + { + strncpy(g_pcTmpBuf, argv[1], sizeof(g_pcTmpBuf)); + } + } + + // + // If the argument is .. then attempt to remove the lowest level on the + // CWD. + // + else if(!strcmp(argv[1], "..")) + { + // + // Get the index to the last character in the current path. + // + ui8Idx = strlen(g_pcTmpBuf) - 1; + + // + // Back up from the end of the path name until a separator (/) is + // found, or until we bump up to the start of the path. + // + while((g_pcTmpBuf[ui8Idx] != '/') && (ui8Idx > 1)) + { + // + // Back up one character. + // + ui8Idx--; + } + + // + // Now we are either at the lowest level separator in the current path, + // or at the beginning of the string (root). So set the new end of + // string here, effectively removing that last part of the path. + // + g_pcTmpBuf[ui8Idx] = 0; + } + + // + // Otherwise this is just a normal path name from the current directory, + // and it needs to be appended to the current path. + // + else + { + // + // Test to make sure that when the new additional path is added on to + // the current path, there is room in the buffer for the full new path. + // It needs to include a new separator, and a trailing null character. + // + if(strlen(g_pcTmpBuf) + strlen(argv[1]) + 1 + 1 > sizeof(g_pcCwdBuf)) + { + UARTprintf("Resulting path name is too long\n"); + return(0); + } + + // + // The new path is okay, so add the separator and then append the new + // directory to the path. + // + else + { + // + // If not already at the root level, then append a / + // + if(strcmp(g_pcTmpBuf, "/")) + { + strcat(g_pcTmpBuf, "/"); + } + + // + // Append the new directory to the path. + // + strcat(g_pcTmpBuf, argv[1]); + } + } + + // + // At this point, a candidate new directory path is in chTmpBuf. Try to + // open it to make sure it is valid. + // + iFResult = f_opendir(&g_sDirObject, g_pcTmpBuf); + + // + // If it can't be opened, then it is a bad path. Inform the user and + // return. + // + if(iFResult != FR_OK) + { + UARTprintf("cd: %s\n", g_pcTmpBuf); + return((int)iFResult); + } + + // + // Otherwise, it is a valid new path, so copy it into the CWD. + // + else + { + strncpy(g_pcCwdBuf, g_pcTmpBuf, sizeof(g_pcCwdBuf)); + } + + // + // Return success. + // + return(0); +} + +//***************************************************************************** +// +// This function implements the "pwd" command. It simply prints the current +// working directory. +// +//***************************************************************************** +int +Cmd_pwd(int argc, char *argv[]) +{ + // + // Print the CWD to the console. + // + UARTprintf("%s\n", g_pcCwdBuf); + + // + // Return success. + // + return(0); +} + +//***************************************************************************** +// +// This function implements the "cat" command. It reads the contents of a file +// and prints it to the console. This should only be used on text files. If +// it is used on a binary file, then a bunch of garbage is likely to printed on +// the console. +// +//***************************************************************************** +int +Cmd_cat(int argc, char *argv[]) +{ + FRESULT iFResult; + uint32_t ui32BytesRead; + + // + // First, check to make sure that the current path (CWD), plus the file + // name, plus a separator and trailing null, will all fit in the temporary + // buffer that will be used to hold the file name. The file name must be + // fully specified, with path, to FatFs. + // + if(strlen(g_pcCwdBuf) + strlen(argv[1]) + 1 + 1 > sizeof(g_pcTmpBuf)) + { + UARTprintf("Resulting path name is too long\n"); + return(0); + } + + // + // Copy the current path to the temporary buffer so it can be manipulated. + // + strcpy(g_pcTmpBuf, g_pcCwdBuf); + + // + // If not already at the root level, then append a separator. + // + if(strcmp("/", g_pcCwdBuf)) + { + strcat(g_pcTmpBuf, "/"); + } + + // + // Now finally, append the file name to result in a fully specified file. + // + strcat(g_pcTmpBuf, argv[1]); + + // + // Open the file for reading. + // + iFResult = f_open(&g_sFileObject, g_pcTmpBuf, FA_READ); + + // + // If there was some problem opening the file, then return an error. + // + if(iFResult != FR_OK) + { + return((int)iFResult); + } + + // + // Enter a loop to repeatedly read data from the file and display it, until + // the end of the file is reached. + // + do + { + // + // Read a block of data from the file. Read as much as can fit in the + // temporary buffer, including a space for the trailing null. + // + iFResult = f_read(&g_sFileObject, g_pcTmpBuf, sizeof(g_pcTmpBuf) - 1, + (UINT *)&ui32BytesRead); + + // + // If there was an error reading, then print a newline and return the + // error to the user. + // + if(iFResult != FR_OK) + { + UARTprintf("\n"); + return((int)iFResult); + } + + // + // Null terminate the last block that was read to make it a null + // terminated string that can be used with printf. + // + g_pcTmpBuf[ui32BytesRead] = 0; + + // + // Print the last chunk of the file that was received. + // + UARTprintf("%s", g_pcTmpBuf); + } + while(ui32BytesRead == sizeof(g_pcTmpBuf) - 1); + + // + // Return success. + // + return(0); +} + +//***************************************************************************** +// +// This function implements the "help" command. It prints a simple list of the +// available commands with a brief description. +// +//***************************************************************************** +int +Cmd_help(int argc, char *argv[]) +{ + tCmdLineEntry *psEntry; + + // + // Print some header text. + // + UARTprintf("\nAvailable commands\n"); + UARTprintf("------------------\n"); + + // + // Point at the beginning of the command table. + // + psEntry = &g_psCmdTable[0]; + + // + // Enter a loop to read each entry from the command table. The end of the + // table has been reached when the command name is NULL. + // + while(psEntry->pcCmd) + { + // + // Print the command name and the brief description. + // + UARTprintf("%6s: %s\n", psEntry->pcCmd, psEntry->pcHelp); + + // + // Advance to the next entry in the table. + // + psEntry++; + } + + // + // Return success. + // + return(0); +} + +//***************************************************************************** +// +// This is the table that holds the command names, implementing functions, and +// brief description. +// +//***************************************************************************** +tCmdLineEntry g_psCmdTable[] = +{ + { "help", Cmd_help, "Display list of commands" }, + { "h", Cmd_help, "alias for help" }, + { "?", Cmd_help, "alias for help" }, + { "ls", Cmd_ls, "Display list of files" }, + { "chdir", Cmd_cd, "Change directory" }, + { "cd", Cmd_cd, "alias for chdir" }, + { "pwd", Cmd_pwd, "Show current working directory" }, + { "cat", Cmd_cat, "Show contents of a text file" }, + { 0, 0, 0 } +}; + +//***************************************************************************** +// +// The error routine that is called if the driver library encounters an error. +// +//***************************************************************************** +#ifdef DEBUG +void +__error__(char *pcFilename, uint32_t ui32Line) +{ +} +#endif + +//***************************************************************************** +// +// Configure the UART and its pins. This must be called before UARTprintf(). +// +//***************************************************************************** +void +ConfigureUART(void) +{ + // + // Enable the GPIO Peripheral used by the UART. + // + ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA); + + // + // Enable UART0 + // + ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0); + + // + // Configure GPIO Pins for UART mode. + // + ROM_GPIOPinConfigure(GPIO_PA0_U0RX); + ROM_GPIOPinConfigure(GPIO_PA1_U0TX); + ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1); + + // + // Initialize the UART for console I/O. + // + UARTStdioConfig(0, 115200, ROM_SysCtlClockGet()); +} + +//***************************************************************************** +// +// The program main function. It performs initialization, then runs a command +// processing loop to read commands from the console. +// +//***************************************************************************** +int +main(void) +{ + int nStatus; + FRESULT iFResult; + tRectangle sRect; + + // + // Enable lazy stacking for interrupt handlers. This allows floating-point + // instructions to be used within interrupt handlers, but at the expense of + // extra stack usage. + // + ROM_FPULazyStackingEnable(); + + // + // Set the system clock to run at 50MHz from the PLL. + // + ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | + SYSCTL_XTAL_16MHZ); + + // + // Enable the peripherals used by this example. + // + ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_SSI0); + + // + // Configure SysTick for a 100Hz interrupt. The FatFs driver wants a 10 ms + // tick. + // + ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / 100); + ROM_SysTickEnable(); + ROM_SysTickIntEnable(); + + // + // Enable Interrupts + // + ROM_IntMasterEnable(); + + // + // Initialize the UART as a console for text I/O. + // + ConfigureUART(); + + // + // Initialize the display driver. + // + CFAL96x64x16Init(); + + // + // Initialize the graphics context. + // + GrContextInit(&g_sContext, &g_sCFAL96x64x16); + + // + // Fill the top part of the screen with blue to create the banner. + // + sRect.i16XMin = 0; + sRect.i16YMin = 0; + sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1; + sRect.i16YMax = 9; + GrContextForegroundSet(&g_sContext, ClrDarkBlue); + GrRectFill(&g_sContext, &sRect); + + // + // Change foreground for white text. + // + GrContextForegroundSet(&g_sContext, ClrWhite); + + // + // Put the application name in the middle of the banner. + // + GrContextFontSet(&g_sContext, g_psFontFixed6x8); + GrStringDrawCentered(&g_sContext, "sd_card", -1, + GrContextDpyWidthGet(&g_sContext) / 2, 4, 0); + + // + // Show some instructions on the display + // + GrContextFontSet(&g_sContext, g_psFontFixed6x8); + GrStringDrawCentered(&g_sContext, "Connect a", -1, + GrContextDpyWidthGet(&g_sContext) / 2, 20, false); + GrStringDrawCentered(&g_sContext, "terminal", -1, + GrContextDpyWidthGet(&g_sContext) / 2, 30, false); + GrStringDrawCentered(&g_sContext, "to UART0.", -1, + GrContextDpyWidthGet(&g_sContext) / 2, 40, false); + GrStringDrawCentered(&g_sContext, "115000,N,8,1", -1, + GrContextDpyWidthGet(&g_sContext) / 2, 50, false); + + // + // Print hello message to user. + // + UARTprintf("\n\nSD Card Example Program\n"); + UARTprintf("Type \'help\' for help.\n"); + + // + // Mount the file system, using logical disk 0. + // + iFResult = f_mount(0, &g_sFatFs); + if(iFResult != FR_OK) + { + UARTprintf("f_mount error: %s\n", StringFromFResult(iFResult)); + return(1); + } + + // + // Enter an infinite loop for reading and processing commands from the + // user. + // + while(1) + { + // + // Print a prompt to the console. Show the CWD. + // + UARTprintf("\n%s> ", g_pcCwdBuf); + + // + // Get a line of text from the user. + // + UARTgets(g_pcCmdBuf, sizeof(g_pcCmdBuf)); + + // + // Pass the line from the user to the command processor. It will be + // parsed and valid commands executed. + // + nStatus = CmdLineProcess(g_pcCmdBuf); + + // + // Handle the case of bad command. + // + if(nStatus == CMDLINE_BAD_CMD) + { + UARTprintf("Bad command!\n"); + } + + // + // Handle the case of too many arguments. + // + else if(nStatus == CMDLINE_TOO_MANY_ARGS) + { + UARTprintf("Too many arguments for command processor!\n"); + } + + // + // Otherwise the command was executed. Print the error code if one was + // returned. + // + else if(nStatus != 0) + { + UARTprintf("Command returned error code %s\n", + StringFromFResult((FRESULT)nStatus)); + } + } +} -- cgit v1.3.1