From c3e4c9a25c2910d2d66d52215b3406b13d5b23d5 Mon Sep 17 00:00:00 2001 From: Yuval Adam Date: Sun, 29 Jun 2014 12:34:32 +0300 Subject: Add more board models --- boards/dk-tm4c129x/usb_host_mouse/usb_host_mouse.c | 553 +++++++++++++++++++++ 1 file changed, 553 insertions(+) create mode 100644 boards/dk-tm4c129x/usb_host_mouse/usb_host_mouse.c (limited to 'boards/dk-tm4c129x/usb_host_mouse/usb_host_mouse.c') diff --git a/boards/dk-tm4c129x/usb_host_mouse/usb_host_mouse.c b/boards/dk-tm4c129x/usb_host_mouse/usb_host_mouse.c new file mode 100644 index 0000000..268ba51 --- /dev/null +++ b/boards/dk-tm4c129x/usb_host_mouse/usb_host_mouse.c @@ -0,0 +1,553 @@ +//***************************************************************************** +// +// usb_host_mouse.c - An example using that supports a mouse. +// +// Copyright (c) 2013-2014 Texas Instruments Incorporated. All rights reserved. +// Software License Agreement +// +// Texas Instruments (TI) is supplying this software for use solely and +// exclusively on TI's microcontroller products. The software is owned by +// TI and/or its suppliers, and is protected under applicable copyright +// laws. You may not combine this software with "viral" open-source +// software in order to form a larger program. +// +// THIS SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS. +// NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT +// NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR +// A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. TI SHALL NOT, UNDER ANY +// CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL +// DAMAGES, FOR ANY REASON WHATSOEVER. +// +// This is part of revision 2.1.0.12573 of the DK-TM4C129X Firmware Package. +// +//***************************************************************************** + +#include +#include +#include +#include "inc/hw_memmap.h" +#include "driverlib/gpio.h" +#include "driverlib/interrupt.h" +#include "driverlib/sysctl.h" +#include "driverlib/rom.h" +#include "driverlib/rom_map.h" +#include "usblib/usblib.h" +#include "usblib/usbhid.h" +#include "usblib/host/usbhost.h" +#include "usblib/host/usbhhid.h" +#include "usblib/host/usbhhidmouse.h" +#include "drivers/pinout.h" +#include "mouse_ui.h" + +//***************************************************************************** +// +//! \addtogroup example_list +//!

USB Host mouse example(usb_host_mouse)

+//! +//! This example application demonstrates how to support a USB mouse using +//! the DK-TM4C129X development board. This application supports only a +//! standard mouse HID device, but can report on the types of other devices +//! that are connected without having the ability to access them. +//! The bottom left status bar reports the +//! type of device attached. The user interface for the application is +//! handled in the mouse_ui.c file while the usb_host_mouse.c file +//! handles start up and the USB interface. +//! +//! The application can be recompiled to run using and external USB phy to +//! implement a high speed host using an external USB phy. To use the external +//! phy the application must be built with \b USE_ULPI defined. This disables +//! the internal phy and the connector on the DK-TM4C129X board and enables the +//! connections to the external ULPI phy pins on the DK-TM4C129X board. +// +//***************************************************************************** + +//***************************************************************************** +// +// The size of the host controller's memory pool in bytes. +// +//***************************************************************************** +#define HCD_MEMORY_SIZE 128 + +//***************************************************************************** +// +// The global application status structure. +// +//***************************************************************************** +tMouseStatus g_sStatus; + +//***************************************************************************** +// +// The memory pool to provide to the Host controller driver. +// +//***************************************************************************** +uint8_t g_pui8HCDPool[HCD_MEMORY_SIZE * MAX_USB_DEVICES]; + +//***************************************************************************** +// +// Declare the USB Events driver interface. +// +//***************************************************************************** +DECLARE_EVENT_DRIVER(g_sUSBEventDriver, 0, 0, USBHCDEvents); + +//***************************************************************************** +// +// The global that holds all of the host drivers in use in the application. +// In this case, only the HID class is loaded. +// +//***************************************************************************** +static tUSBHostClassDriver const * const g_ppHostClassDrivers[] = +{ + &g_sUSBHIDClassDriver, + &g_sUSBEventDriver +}; + +//***************************************************************************** +// +// This global holds the number of class drivers in the g_ppHostClassDrivers +// list. +// +//***************************************************************************** +static const uint32_t g_ui32NumHostClassDrivers = + sizeof(g_ppHostClassDrivers) / sizeof(tUSBHostClassDriver *); + +//***************************************************************************** +// +// The global value used to store the mouse instance value. +// +//***************************************************************************** +static tUSBHMouse *g_psMouse; + +//***************************************************************************** +// +// The error routine that is called if the driver library encounters an error. +// +//***************************************************************************** +#ifdef DEBUG +void +__error__(char *pcFilename, uint32_t ui32Line) +{ +} +#endif + +//***************************************************************************** +// +// This enumerated type is used to hold the states of the mouse. +// +//***************************************************************************** +enum +{ + // + // No device is present. + // + eStateNoDevice, + + // + // Mouse has been detected and needs to be initialized in the main loop. + // + eStateMouseInit, + + // + // Mouse is connected and waiting for events. + // + eStateMouseConnected, +} +g_iMouseState; + +//***************************************************************************** +// +// This is the callback from the USB HID mouse handler. +// +// pvCBData is ignored by this function. +// ui32Event is one of the valid events for a mouse device. +// ui32MsgParam is defined by the event that occurs. +// pvMsgData is a pointer to data that is defined by the event that +// occurs. +// +// This function will be called to inform the application when a mouse has +// been plugged in or removed and any time a mouse movement or button pressed +// has occurred. +// +// This function will return 0. +// +//***************************************************************************** +void +MouseCallback(tUSBHMouse *psMouse, uint32_t ui32Event, uint32_t ui32MsgParam, + void *pvMsgData) +{ + int32_t i32Pos; + + switch(ui32Event) + { + // + // New mouse detected. + // + case USB_EVENT_CONNECTED: + { + // + // Proceed to the eStateMouseInit state so that the main loop + // can finish initializing the mouse since USBHMouseInit() cannot + // be called from within a callback. + // + g_iMouseState = eStateMouseInit; + + break; + } + + // + // Mouse has been unplugged. + // + case USB_EVENT_DISCONNECTED: + { + // + // Change the state so that the main loop knows that a device is no + // longer present. + // + g_iMouseState = eStateNoDevice; + + // + // Need to clear out any held buttons. + // + g_sStatus.ui32Buttons = 0; + + g_sStatus.bUpdate = true; + + break; + } + + // + // New button press detected. + // + case USBH_EVENT_HID_MS_PRESS: + { + // + // Save the new button that was pressed. + // + g_sStatus.ui32Buttons |= ui32MsgParam; + + g_sStatus.bUpdate = true; + + break; + } + + // + // A button was released on a HID mouse. + // + case USBH_EVENT_HID_MS_REL: + { + // + // Remove the button from the pressed state. + // + g_sStatus.ui32Buttons &= ~ui32MsgParam; + + g_sStatus.bUpdate = true; + + break; + } + + // + // The HID mouse detected movement in the X direction. + // + case USBH_EVENT_HID_MS_X: + { + // + // Update the cursor X position. + // This has to be calculated as an intermediate signed value + // because the position can go negative with fast movements. + // + i32Pos = g_sStatus.ui32XPos + (int8_t)ui32MsgParam; + + if(i32Pos < 0) + { + g_sStatus.ui32XPos = MOUSE_MIN_X; + } + else + { + g_sStatus.ui32XPos = (uint32_t)i32Pos; + } + + if(g_sStatus.ui32XPos < MOUSE_MIN_X) + { + g_sStatus.ui32XPos = MOUSE_MIN_X; + } + + if(g_sStatus.ui32XPos > MOUSE_MAX_X) + { + g_sStatus.ui32XPos = MOUSE_MAX_X; + } + + g_sStatus.bUpdate = true; + + break; + } + + // + // The HID mouse detected movement in the Y direction. + // + case USBH_EVENT_HID_MS_Y: + { + // + // Update the cursor Y position. + // This has to be calculated as an intermediate signed value + // because the position can go negative with fast movements. + // + i32Pos = (int32_t)g_sStatus.ui32YPos + (int8_t)ui32MsgParam; + + if(i32Pos < 0) + { + g_sStatus.ui32YPos = MOUSE_MIN_Y; + } + else + { + g_sStatus.ui32YPos = (uint32_t)i32Pos; + } + + if(g_sStatus.ui32YPos < MOUSE_MIN_Y) + { + g_sStatus.ui32YPos = MOUSE_MIN_Y; + } + + if(g_sStatus.ui32YPos > MOUSE_MAX_Y) + { + g_sStatus.ui32YPos = MOUSE_MAX_Y; + } + + g_sStatus.bUpdate = true; + + break; + } + default: + { + break; + } + } +} + +//***************************************************************************** +// +// The main routine for handling the USB mouse. +// +//***************************************************************************** +void +MouseMain(void) +{ + switch(g_iMouseState) + { + // + // This state is entered when they mouse is first detected. + // + case eStateMouseInit: + { + // + // Initialized the newly connected mouse. + // + USBHMouseInit(g_psMouse); + + // + // Proceed to the mouse connected state. + // + g_iMouseState = eStateMouseConnected; + + break; + } + case eStateMouseConnected: + default: + { + if(g_sStatus.bUpdate == true) + { + g_sStatus.bUpdate = false; + + UIUpdateStatus(); + } + break; + } + } +} + +//***************************************************************************** +// +// This is the generic callback from host stack. +// +// pvData is actually a pointer to a tEventInfo structure. +// +// This function will be called to inform the application when a USB event has +// occurred that is outside those related to the mouse device. At this +// point this is used to detect unsupported devices being inserted and removed. +// It is also used to inform the application when a power fault has occurred. +// This function is required when the g_USBGenericEventDriver is included in +// the host controller driver array that is passed in to the +// USBHCDRegisterDrivers() function. +// +//***************************************************************************** +void +USBHCDEvents(void *pvData) +{ + tEventInfo *pEventInfo; + + // + // Cast this pointer to its actual type. + // + pEventInfo = (tEventInfo *)pvData; + + switch(pEventInfo->ui32Event) + { + case USB_EVENT_UNKNOWN_CONNECTED: + case USB_EVENT_CONNECTED: + { + // + // Save the device instance data. + // + g_sStatus.ui32Instance = pEventInfo->ui32Instance; + g_sStatus.bConnected = true; + + // + // Update the port status for the new device. + // + UIUpdateStatus(); + + break; + } + // + // A device has been unplugged. + // + case USB_EVENT_DISCONNECTED: + { + // + // Device is no longer connected. + // + g_sStatus.bConnected = false; + + // + // Update the port status for the new device. + // + UIUpdateStatus(); + + break; + } + default: + { + break; + } + } +} + +//***************************************************************************** +// +// The main application loop. +// +//***************************************************************************** +int +main(void) +{ + uint32_t ui32SysClock, ui32PLLRate; +#ifdef USE_ULPI + uint32_t ui32Setting; +#endif + + // + // Set the application to run at 120 MHz with a PLL frequency of 480 MHz. + // + ui32SysClock = MAP_SysCtlClockFreqSet((SYSCTL_XTAL_25MHZ | + SYSCTL_OSC_MAIN | SYSCTL_USE_PLL | + SYSCTL_CFG_VCO_480), 120000000); + + // + // Set the part pin out appropriately for this device. + // + PinoutSet(); + +#ifdef USE_ULPI + // + // Switch the USB ULPI Pins over. + // + USBULPIPinoutSet(); + + // + // Enable USB ULPI with high speed support. + // + ui32Setting = USBLIB_FEATURE_ULPI_HS; + USBOTGFeatureSet(0, USBLIB_FEATURE_USBULPI, &ui32Setting); + + // + // Setting the PLL frequency to zero tells the USB library to use the + // external USB clock. + // + ui32PLLRate = 0; +#else + // + // Save the PLL rate used by this application. + // + ui32PLLRate = 480000000; +#endif + + // + // Initialize the connection status. + // + g_sStatus.bConnected = false; + g_sStatus.ui32Buttons = 0; + + // + // Enable Clocking to the USB controller. + // + ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0); + + // + // Enable Interrupts + // + ROM_IntMasterEnable(); + + // + // Initialize the USB stack mode and pass in a mode callback. + // + USBStackModeSet(0, eUSBModeHost, 0); + + // + // Register the host class drivers. + // + USBHCDRegisterDrivers(0, g_ppHostClassDrivers, g_ui32NumHostClassDrivers); + + // + // Open an instance of the mouse driver. The mouse does not need + // to be present at this time, this just save a place for it and allows + // the applications to be notified when a mouse is present. + // + g_psMouse = USBHMouseOpen(MouseCallback, 0, 0); + + // + // Initialize the power configuration. This sets the power enable signal + // to be active high and does not enable the power fault. + // + USBHCDPowerConfigInit(0, USBHCD_VBUS_AUTO_HIGH | USBHCD_VBUS_FILTER); + + // + // Tell the USB library the CPU clock and the PLL frequency. This is a + // new requirement for TM4C129 devices. + // + USBHCDFeatureSet(0, USBLIB_FEATURE_CPUCLK, &ui32SysClock); + USBHCDFeatureSet(0, USBLIB_FEATURE_USBPLL, &ui32PLLRate); + + // + // Initialize the USB controller for Host mode. + // + USBHCDInit(0, g_pui8HCDPool, sizeof(g_pui8HCDPool)); + + // + // Initialize the UI elements. + // + UIInit(ui32SysClock); + + // + // The main loop for the application. + // + while(1) + { + // + // Call the USB library to let non-interrupt code run. + // + USBHCDMain(); + + // + // Call the mouse and mass storage main routines. + // + MouseMain(); + } +} -- cgit v1.3.1